Export limit exceeded: 381902 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Export limit exceeded: 381902 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (381902 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-74653 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: serial: 8250_of: clear stuck empty-FIFO RX-timeout on LPC32xx The NXP LPC32xx UART (PORT_LPC3220) can latch an RX character-timeout interrupt while the RX FIFO is empty: IIR reports UART_IIR_RX_TIMEOUT (0x0c) but LSR.DR is clear. A character timeout is only cleared by reading RHR, but serial8250_rx_chars() reads RHR only when LSR.DR is set, so nothing ever clears the condition. The interrupt is level-triggered and re-fires immediately, so on a single-core ARM926 the resulting interrupt storm livelocks the CPU. It is reproducible when userspace repeatedly opens the front-panel port (ttyS1): serial8250_do_set_termios() re-enables interrupts on unlock and the handler then spins forever with iir=0xcc lsr=0x60 ier=0x05, tripping the soft-lockup detector in serial8250_handle_irq_locked(). LPC32xx has no dedicated 8250 glue driver, it's driven by the generic 8250_of. Add a hardware specific handle_irq for PORT_LPC3220, wired up in of_platform_serial_setup() the same way fsl8250_handle_irq is installed. The handler follows dw8250_handle_irq(): on an RX timeout with an empty FIFO (LSR.DR and LSR.BI clear) it does one throwaway RHR read to clear the condition, then calls serial8250_handle_irq_locked(). No real received data is ever discarded, and it is a no-op on healthy UARTs which never report a timeout with DR clear. This is the same class of bug already worked around in other 8250 drivers; see commit 424d79183af0 ("serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt") which reports the identical iir=0xcc/lsr=0x60. See also UART_RX_TIMEOUT_QUIRK in 8250_omap, and the note in 8250_bcm7271. | ||||
| CVE-2026-74652 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: serial: amba-pl011: cancel RS485 hrtimers after freeing IRQ The RS485 trigger hrtimers are embedded in the devm-managed port and can fire after it is freed. The IRQ handler can arm a timer, so free the IRQ first and then cancel both timers. Complete the RS485 stop without arming a timer, and cancel the timers in remove() for the suspend-then-unbind path, where shutdown is not called. This issue was found by an in-house static analysis tool. | ||||
| CVE-2026-74651 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB read in rtw_get_wpa_ie() rtw_get_wpa_ie() reads bytes at fixed offsets into a vendor-specific information element without checking that the element is long enough, causing an out-of-bounds read for a short trailing IE. The function locates a vendor-specific IE (EID 221) with rtw_get_ie() and then compares a 4-byte OUI+type at pbuf + 2 and reads a 2-byte version word at pbuf + 6. Those accesses require the IE body to be at least 6 bytes, but rtw_get_ie() only guarantees that the element fits within the buffer; it does not enforce a minimum body length. A vendor-specific IE whose length byte is 0 to 5, placed at the end of the buffer, therefore makes these reads run past the end of the IE and past the end of the buffer itself. The buffer holds information elements taken from received management frames and from the IE blob passed to rtw_cfg80211_set_wpa_ie(), which is kmemdup'd to its exact length, so the read can run off the end of the allocation. The sibling helpers rtw_get_sec_ie(), rtw_get_wapi_ie() and rtw_get_wps_ie() in this file already reject too-short vendor-specific IEs before their OUI memcmp(); rtw_get_wpa_ie() was never brought in line with them, and needs a minimum of 6 rather than 4 bytes because of the version word. Add the missing length check. | ||||
| CVE-2026-74650 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB read in WMM_param_handler() WMM_param_handler() copies a fixed-size WMM parameter element out of a received information element without checking that the element is long enough, causing an out-of-bounds read for a short WMM IE. The handler reads sizeof(struct WMM_para_element) (18) bytes at pIE->data + 6, so it requires pIE->length to be at least 24 (WLAN_WMM_LEN), but it never validates the length. Two of its three callers reach it after matching only the WMM OUI: OnAssocRsp() in rtw_mlme_ext.c matches a 6-byte OUI, and join_cmd_hdl() matches a 4-byte OUI, before calling the handler. A vendor-specific IE carrying the WMM OUI but a length between 6 and 23, placed in an association response or in the IE blob handed to join_cmd_hdl(), passes the OUI check and then makes the memcmp() and memcpy() at pIE->data + 6 read past the end of the element. OnAssocRsp() parses a frame received from the AP, so this is reachable from a remote peer. The remaining caller in rtw_wlan_util.c already guards the handler with "pIE->length == WLAN_WMM_LEN". Move the equivalent check into the handler itself so every caller is covered; the sibling IE handlers in the same parsing loop (HT_caps_handler(), HT_info_handler(), ERP_IE_handler()) likewise bound their accesses by pIE->length. | ||||
| CVE-2026-74649 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix missing shared-key auth challenge length check The WEP shared-key authentication handler uses the challenge-text element's attacker-controlled length without checking it against the fixed 128-byte chg_txt buffer. In OnAuthClient() the length from rtw_get_ie() - up to 255 - is used to perform memcpy() into the 128-byte pmlmeinfo->chg_txt, so a malicious AP sending a malformed WLAN_EID_CHALLENGE element can overflow/underfill chg_txt by up to 127 bytes. It is reachable over the air, before association, during shared-key authentication. In the case of an overflow, the driver can write out of bounds. In the case of an underfill, the driver can echo stale buffer memory. The challenge text is defined to be exactly 128 octets, which is already provided as the WLAN_AUTH_CHALLENGE_LEN define; require the element to be exactly that length before use. | ||||
| CVE-2026-74648 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: validate monitor transmit frame lengths rtw_cfg80211_monitor_if_xmit_entry() removes the radiotap header and then reads the 802.11 frame control field without checking that a base 802.11 header remains. The data path also pulls the calculated 802.11, QoS and SNAP header span before confirming that the skb contains it. A truncated frame can therefore cause out-of-bounds reads or leave insufficient data for the Ethernet address writes. Reject frames that do not contain the base 802.11 header and data frames that do not contain their complete calculated header span. | ||||
| CVE-2026-74647 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: Remove buffer from list prior to unmap operation fastrpc_req_munmap_impl() is called to unmap any buffer. The buffer is getting removed from the list after it is unmapped from DSP. This can create potential race conditions if multiple threads invoke unmap concurrently, where one thread may remove the entry from the list while another thread's unmap operation is still ongoing. Fix this by removing the buffer entry from the list before calling the unmap operation. If the unmap fails, the entry is re-added to the list so that userspace can retry the unmap, or alternatively, the buffer will be cleaned up during device release when the DSP process is torn down and all DSP-side mappings are freed along with remaining buffers in the list. | ||||
| CVE-2026-74646 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: take fl->lock when moving mmaps on interrupted invoke When an invoke is interrupted by a signal, wait_for_completion_interruptible() returns -ERESTARTSYS and fastrpc_internal_invoke() moves every buffer from fl->mmaps onto cctx->invoke_interrupted_mmaps. This list_del()/list_add_tail() walk runs without holding fl->lock, the lock that serialises fl->mmaps in fastrpc_req_mmap() and fastrpc_req_munmap() everywhere else. Take fl->lock around the move, matching every other fl->mmaps accessor. | ||||
| CVE-2026-74645 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mm/damon/lru_sort: error out for >10000 active_mem_bp damos_quota_score() can trigger division by zero if the target value is zero. DAMON_LRU_SORT lets users set the target value for the hot memory scheme via active_mem_bp parameter. It avoids setting it as the target value if the parameter value is zero. However, it also sets the cold memory scheme with a target value that is calculated as '10000 - active_mem_bp + 2'. Hence, if a user sets active_mem_bp 10002, the cold memory scheme's quota goal target value can be zero. As a result, division by zero can be triggered. Fix by returning an error when the user tries to start DAMON with >10000 active_mem_bp parameter value. It makes no sense to set active_mem_bp with 10002. It also requires module parameters write permission to reproduce the issue. That said, the consequence is quite bad. One reliable way to reproduce the issue is like below: # cd /sys/module/damon_lru_sort/parameters # echo 1000 > wmarks_high # echo 995 > wmarks_mid # echo 0 > wmarks_low # echo 10002 > active_mem_bp # echo Y > enabled # dmesg -w [...] [ 597.421247] Oops: divide error: 0000 [#1] SMP NOPTI [ 597.428848] RIP: 0010:damos_quota_score+0x6f/0x480 This issue was discovered [1] by Sashiko. | ||||
| CVE-2026-74644 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mm/damon/ops-common: putback folios on invalid migrate nid damon_pa_migrate() and damos_va_migrate() isolate folios into a local list and then call damon_migrate_pages(). When target_nid is invalid (including the scheme default NUMA_NO_NODE / -1), damon_migrate_pages() returns early without putting the folios back to the LRU. Callers then discard the list head while those folios remain isolated with an extra reference taken by folio_isolate_lru(). The pages stay off the LRU for as long as the mapping exists (anon active+inactive counts drop while RSS does not), and the leftover references can pin the pages after the mapping is gone. Put the folios back on the invalid-nid path so ignored migration requests still return them to the LRU. | ||||
| CVE-2026-74643 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: samples/damon/mtier: error out for zero quota goal target values Patch series "mm/damon: avoid division by zero from damos_quota_score()". DAMON_SAMPLE_MTIER and DAMON_LRU_SORT allow the user to trigger division by zero in damos_quota_score(). Avoid it by adding parameters validation checks. This patch (of 2): damos_quota_score() can trigger division by zero if the target_value is zero. DAMON_SAMPLE_MTIER lets users set the target_value via node0_mem_{used,free}_bp parameters. It doesn't guard zero value case, though. As a result, users can trigger division by zero. Fix the issue by returning an error when the user tries to start DAMON with zero node0_mem_{used,free}_bp parameter values. DAMON_SAMPLE_MTIER is just a sample module, but the consequence is quite bad. Also the zero node0_mem_free_bp parameter might look like a reasonable setup to some users. Hence, the issue might really happen in the real world. One reliable way to reproduce the issue is like below: # cd /sys/module/damon_sample_mtier/parameters # echo 4096 > node0_start_addr # echo 8192 > node0_end_addr # echo 8192 > node1_start_addr # echo 81920 > node1_end_addr # echo 0 > node0_mem_free_bp # echo Y > enabled # dmesg -w [...] [18792.235916] Oops: divide error: 0000 [#1] SMP NOPTI [...] [18792.242787] RIP: 0010:damos_quota_score+0x6f/0x480 [...] This issue was discovered [1] by Sashiko. | ||||
| CVE-2026-74642 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: usb: Fix UAF at delayed release of MIDI2 EPs The recent fix for UAF in ump_to_endpoint() caused another UAF because it tries to dereference the UMP endpoint object, but this might be executed at a delayed context where the endpoint has been already released. Add private_free to clear the associated data for avoiding the further dereference for delayed releases. | ||||
| CVE-2026-74641 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: usx2y: bound the hwdep mmap fault offset snd_us428ctls_vm_fault() turns the faulting page offset into a kernel address with no bound of any kind: offset = vmf->pgoff << PAGE_SHIFT; vaddr = (char *)(...)->us428ctls_sharedmem + offset; page = virt_to_page(vaddr); get_page(page); vmf->page = page; return 0; snd_us428ctls_mmap() checks only the length of the mapping, never the offset, and us428ctls_sharedmem is a single page from alloc_pages_exact(). For a character device file_mmap_size_max() returns ULONG_MAX, so the mm layer imposes no ceiling either. Every page offset above zero resolves to a struct page outside the object, and the handler installs it into the caller's address space read-write; the vma is not marked read-only. The caller picks the page frame with a single mmap() argument and gets read-write access to a page of kernel memory it does not own; an offset that lands in an unpopulated vmemmap region oopses instead. A process that can open the hwdep node of an attached US-X2Y reaches this after loading the FPGA image through the same node; no capability check is involved. On 7.2.0-rc5 (arm64), mmap() with a large offset: Unable to handle kernel paging request at virtual address fffffdffc45d5ac8 pc : snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y] Call trace: snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y] __do_fault __handle_mm_fault handle_mm_fault el0_da Reject any offset outside the shared region. The pcm hwdep handler in usx2yhwdeppcm.c computes its address the same way and needs the same bound. Discovered by XBOW, triaged by Baul Lee <[email protected]> | ||||
| CVE-2026-74640 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: FCP: fix OOB write in fcp_meter_ctl_get() fcp_ioctl_set_meter_map() bounds the user-supplied Level Meter map size by the driver's own limit of 255 if (map.map_size < 1 || map.map_size > 255 || map.meter_slots < 1 || map.meter_slots > 255) return -EINVAL; and passes it to fcp_add_new_ctl() as the control's channel count, where it is stored as elem->channels. Every control read writes into struct snd_ctl_elem_value, whose integer array is declared long value[128], so the limit is 128, not 255. fcp_meter_ctl_get() stores one 64-bit word per channel into that array with no bound of its own: for (i = 0; i < elem->channels; i++) { int idx = private->meter_level_map[i]; int value = idx < 0 ? 0 : le32_to_cpu(resp[idx]); ucontrol->value.integer.value[i] = value; } snd_ctl_elem_read_user() serves that object from memdup_user(_control, sizeof(*control)), 1224 bytes on LP64 out of kmalloc-2048. offsetof(struct snd_ctl_elem_value, value) is 72, so element i is written at byte 72 + 8 * i and element 144 already lands past the allocation. At map_size 255 the last store ends at byte 2112, 888 bytes past the object and 64 bytes into the adjacent slab object. The stored words come from the device and meter_level_map[] selects which word lands in which slot, so extent and contents are both controlled. The core does not catch this. snd_ctl_check_elem_info() is reached only from __snd_ctl_elem_info(), which snd_ctl_elem_read() calls under CONFIG_SND_CTL_DEBUG; without that option snd_ctl_skip_validation() is a compile-time true. __snd_ctl_add_replace() validates kcontrol->count and never inspects elem->channels. Installing an oversized map needs CAP_SYS_RAWIO, but the control outlives the hwdep descriptor that created it, so the out-of-bounds stores are issued by any process able to read controls on /dev/snd/controlC0. KASAN on 7.2.0-rc5 (arm64), triggered by an unprivileged control read: BUG: KASAN: slab-out-of-bounds in fcp_meter_ctl_get Write of size 8 at addr ffff000017af04c8 by task fcp_trigger/185 __asan_store8 fcp_meter_ctl_get snd_ctl_elem_read snd_ctl_ioctl Allocated by task 185: memdup_user snd_ctl_ioctl The buggy address is located 0 bytes to the right of allocated 1224-byte region [ffff000017af0000, ffff000017af04c8) Bound the map size by the ABI limit rather than by 255, and bound the store loop at the sink so it cannot run past the value array whatever elem->channels holds. Discovered by XBOW, triaged by Baul Lee <[email protected]> | ||||
| CVE-2026-74639 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: us144mkii: re-anchor capture URBs on resubmission capture_urb_complete() resubmits each capture URB without anchoring it: usb_get_urb(urb); ret = usb_submit_urb(urb, GFP_ATOMIC); Anchoring is a property of a submission, not of the URB. The giveback path calls usb_unanchor_urb() before urb->complete(), so an URB resubmitted from its own completion handler is off the anchor. The capture URBs are anchored once, at stream start, so from the first completion onward tascam->capture_anchor is empty. tascam_free_urbs(), tascam_disconnect(), tascam_suspend() and the stop-work path all call usb_kill_anchored_urbs(&tascam->capture_anchor) to reap the capture URBs before anything is freed. With the anchor empty those calls return immediately and the URBs stay queued on the host controller. tascam_free_urbs() then returns the capture transfer buffers with usb_free_coherent(), and snd_card_free() releases the snd_card allocation that embeds tascam (card->private_data). The controller completes the queued URBs afterwards, writing device-supplied data into the freed transfer buffer, and capture_urb_complete() dereferences the freed driver object. KASAN on 7.2.0-rc5 (arm64): BUG: KASAN: slab-use-after-free in dummy_timer Write of size 512 at addr ffff000015b62000 __asan_memcpy dummy_timer hrtimer_run_softirq Allocated by task 64: usb_alloc_coherent tascam_alloc_urbs tascam_probe Freed by task 170: usb_free_coherent tascam_free_urbs tascam_disconnect usb_unbind_interface BUG: KASAN: slab-use-after-free in capture_urb_complete Read of size 4 at addr ffff0000170ee878 Freed by task 170: release_card_device snd_card_free tascam_disconnect Restore the usb_anchor_urb() between the reference count bump and the resubmission. That also makes the handler's usb_unanchor_urb() failure arm meaningful again and restores usb_kill_anchored_urbs() as a barrier on the disconnect, suspend and stop-work paths. The anchoring was removed on the premise that the URB is already anchored from the initial submission, which does not hold once the first giveback has run. Discovered by XBOW, triaged by Baul Lee <[email protected]> | ||||
| CVE-2026-74638 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Serialize the scheduler timeout handlers V3D exposes several independent hardware queues (BIN, RENDER, TFU and CSD) but has only a single, global reset. A timeout on any one queue therefore has to stop, reset and restart the schedulers of every other queue as well. That makes concurrent timeout handlers unsafe. `reset_lock` was never able to make them safe, as a driver-side lock can only cover the driver's &drm_sched_backend_ops.timedout_job callback. The scheduler handles the timed out job and its pending list around that callback, outside of the driver's control, so a global reset triggered by one queue can still interfere with another queue that is in the middle of handling a timeout of its own. Consequently, if a reset happens in the CSD queue while a CL-intensive application is running, the global reset stops and restarts the CL queue's scheduler while that queue is handling a timeout of its own. As drm_sched_stop() and drm_sched_start() subtract and add the credits of every job sitting on the pending list of the scheduler they are called on, and as the CL queue's handler concurrently takes its job off that same list and puts it back, the stop and the start no longer see the same set of jobs. The CL queue is left with more credits in flight than its limit: [ 327.302739] ------------[ cut here ]------------ [ 327.302744] WARNING: CPU: 2 PID: 43 at drivers/gpu/drm/scheduler/sched_main.c:102 drm_sched_run_job_work+0x238/0x4d0 [gpu_sched] [ 327.302884] CPU: 2 UID: 0 PID: 43 Comm: kworker/u16:1 Not tainted 6.18.39-v8-16k+ #3 PREEMPT [ 327.302889] Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT) [ 327.302893] Workqueue: v3d_bin drm_sched_run_job_work [gpu_sched] [ 327.302984] Call trace: [ 327.302987] drm_sched_run_job_work+0x238/0x4d0 [gpu_sched] (P) [ 327.302997] process_scheduled_works+0x180/0x3d0 [ 327.303010] worker_thread+0x268/0x3e8 [ 327.303016] kthread+0x140/0x250 [ 327.303022] ret_from_fork+0x10/0x20 [ 327.303031] ---[ end trace 0000000000000000 ]--- From that point on, the credit count of the CL queue is broken, causing a complete GPU hang and UI freeze. The DRM scheduler already provides a mechanism to serialize the timeout handlers of different schedulers: an ordered workqueue passed as drm_sched_init()'s @timeout_wq parameter. By default, each scheduler queues its timeout work on the system workqueue, which runs the handlers concurrently. Give all of the queues a shared ordered workqueue instead, as recommended by the DRM scheduler documentation for hardware that has distinct queues but resets globally. | ||||
| CVE-2026-74637 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: perf/core: Fix group leader use-after-free after sibling detach perf_group_detach() handles leader and sibling detach differently. When the group leader is detached, all siblings are promoted to singleton events and their group_leader pointer is reset to themselves. When a sibling is detached, it is removed from the leader's sibling_list, but its group_leader pointer is left pointing at the old leader. That is harmless when the sibling is being closed and freed immediately, as in the DETACH_DEAD path. It is not safe when the sibling is detached but kept alive, such as during CPU hotplug with DETACH_GROUP. In that case the sibling is removed from the context, while its file descriptor can still keep it alive. A typical failing sequence is: - A group contains leader L and sibling S. - CPU hot-unplug detaches S with DETACH_GROUP, removing it from L->sibling_list but leaving S->group_leader == L. - L is later closed and freed. - A PERF_IOC_FLAG_GROUP ioctl on S follows S->group_leader and dereferences the freed leader. This was reproduced by running the perf event fuzzer, CPU hotplug, and a stress workload concurrently: Unable to handle kernel paging request at virtual address 006b6b6b6b6b6cdb CPU: 2 PID: 12489 Comm: perf_fuzzer 6.18.7 PREEMPT pc : perf_ioctl+0x34c/0xc68 x20: ffffff89a3fa2c70 x8 : 6b6b6b6b6b6b6b6b Code: 943c4a0e 340047a0 f9404a94 f9411e88 (f940b908) Call trace: perf_ioctl+0x34c/0xc68 (P) __arm64_sys_ioctl+0xa0/0xf4 invoke_syscall+0x58/0xe4 el0_svc_common+0xa8/0xdc do_el0_svc+0x1c/0x28 el0_svc+0x40/0xc0 el0t_64_sync_handler+0x68/0xdc el0t_64_sync+0x1c4/0x1c8 The fault happened in perf_ioctl(), where perf_event_for_each() follows the stale group_leader pointer and perf_event_for_each_child() then dereferences the freed leader's context. Fix the use-after-free by promoting the detached sibling to a singleton. Also fix __event_disable() cgroup accounting and event state change. | ||||
| CVE-2026-74636 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: tracing: Fix race between update_event_fields and, event_define_fields The following sequence may leads race between event_define_fields() and update_event_fields(): CPU0 (loads module A) CPU1 (loads module B) =============================== =============================== load_module(A) load_module(B) notifier_call_chain notifier_call_chain trace_module_notify trace_module_notify mutex_lock(&event_mutex) trace_event_update_all() trace_module_add_events(A) down_write(&trace_event_sem) __register_event(call_A) __add_event_to_tracers(call_A) event_define_fields(call_A) for each f: list_for_each_entry(field, list_add(&f->link, &class->fields, link) &class->fields) field = class->fields->next; Where access to the class->fields is not protected by the event_mutex in trace_event_update_all(). This produces the following panic: Unable to handle kernel access ... at virtual address 0000000000000018 pc : update_event_fields+0xf8/0x368 Call trace: update_event_fields+0xf8/0x368 trace_event_update_all+0x7c/0x2b4 trace_module_notify+0x4c/0x1dc notifier_call_chain+0x84/0x168 blocking_notifier_call_chain_robust+0x64/0xd4 load_module+0x10c8/0x123c __arm64_sys_finit_module+0x230/0x31c Fix by taking event_mutex in trace_event_update_all() before trace_event_sem. | ||||
| CVE-2026-74635 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: fbdev: bitblit: bound-check glyph index in bit_cursor() bit_cursor() fetches the glyph under the cursor with c = scr_readw(vc_pos); src = vc_font.data + ((c & charmask) * w * height); where charmask is 0x1ff when vc_hi_font_mask is set. The screen buffer value comes directly from scr_readw() and may be larger than the current font's glyph count. Syzkaller triggers this via vcs_write(). The Call Trace shows vcs_write() in vc_screen.c writing an arbitrary 16-bit value with writev() to /dev/vcsa, which vcs_write_buf() in vc_screen.c stores via vcs_scr_writew() without checking charcount. The stored value is later read in bit_cursor() in bitblit.c. When the font is changed from a font with 512 glyphs to a font with 256 glyphs, the screen buffer can retain characters with the high bit set from the previous mode, which could also produce the same out-of-bounds access. BUG: KASAN: global-out-of-bounds in soft_cursor+0x378/0x6bc drivers/video/fbdev/core/softcursor.c:70 Read of size 16 at addr ffff800086c57970 Call Trace: soft_cursor+0x378/0x6bc drivers/video/fbdev/core/softcursor.c:70 bit_cursor+0xa90/0x1108 drivers/video/fbdev/core/bitblit.c:365 fbcon_cursor+0x344/0x498 drivers/video/fbdev/core/fbcon.c:1427 hide_cursor+0xdc/0x2d0 drivers/tty/vt/vt.c:883 update_region+0x100/0x18c drivers/tty/vt/vt.c:669 vcs_write+0x8ec/0xaf0 drivers/tty/vt/vc_screen.c:685 bit_putcs_aligned() and bit_putcs_unaligned() already clamp the glyph index to vc_font.charcount. Apply the same clamp in bit_cursor() after extracting the attribute and masking, before indexing fontdata. The fix completes the bounds checking started in commit 18c4ef4e765a ("fbdev: bitblit: bound-check glyph index in bit_putcs*"), which missed the cursor path. This change should be safe because the clamp reuses the existing contract from fbcon: charcount is maintained under console_lock in con_font_set() and fbcon_font_set(), and hi_font_mask is cleared when switching from 512 to 256 glyphs. When stale screen data with high bits remains after a font switch, or when vcs_write() stores an arbitrary value, clamping the index to 0 prevents the out-of-bounds read without changing cursor semantics — the same fallback bit_putcs uses. | ||||
| CVE-2026-74634 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Prevent subbuf order change when resizing is disabled Because ring_buffer_subbuf_order_set() frees buffer pages, we can't allow it when resizing is disabled. A non-consuming reader is at risk of use-after-free (rb_advance_iter()). Return -EBUSY on resize_disabled, matching ring_buffer_resize() behaviour. | ||||