| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: Fix DMA mappings leak
During reallocation of RX buffers, new DMA mappings are created for
those buffers.
steps for reproduction:
while :
do
for ((i=0; i<=8160; i=i+32))
do
ethtool -G enp130s0f0 rx $i tx $i
sleep 0.5
ethtool -g enp130s0f0
done
done
This resulted in crash:
i40e 0000:01:00.1: Unable to allocate memory for the Rx descriptor ring, size=65536
Driver BUG
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:141 xdp_rxq_info_unreg+0x43/0x50
Call Trace:
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
Missing register, driver bug
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:119 xdp_rxq_info_unreg_mem_model+0x69/0x140
Call Trace:
xdp_rxq_info_unreg+0x1e/0x50
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
This was caused because of new buffers with different RX ring count should
substitute older ones, but those buffers were freed in
i40e_configure_rx_ring and reallocated again with i40e_alloc_rx_bi,
thus kfree on rx_bi caused leak of already mapped DMA.
Fix this by reallocating ZC with rx_bi_zc struct when BPF program loads. Additionally
reallocate back to rx_bi when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XSP_SETUP_XSK_POOL handler. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: vdso: fix NULL deference in vdso_join_timens() when vfork
Testing tools/testing/selftests/timens/vfork_exec.c got below
kernel log:
[ 6.838454] Unable to handle kernel access to user memory without uaccess routines at virtual address 0000000000000020
[ 6.842255] Oops [#1]
[ 6.842871] Modules linked in:
[ 6.844249] CPU: 1 PID: 64 Comm: vfork_exec Not tainted 6.0.0-rc3-rt15+ #8
[ 6.845861] Hardware name: riscv-virtio,qemu (DT)
[ 6.848009] epc : vdso_join_timens+0xd2/0x110
[ 6.850097] ra : vdso_join_timens+0xd2/0x110
[ 6.851164] epc : ffffffff8000635c ra : ffffffff8000635c sp : ff6000000181fbf0
[ 6.852562] gp : ffffffff80cff648 tp : ff60000000fdb700 t0 : 3030303030303030
[ 6.853852] t1 : 0000000000000030 t2 : 3030303030303030 s0 : ff6000000181fc40
[ 6.854984] s1 : ff60000001e6c000 a0 : 0000000000000010 a1 : ffffffff8005654c
[ 6.856221] a2 : 00000000ffffefff a3 : 0000000000000000 a4 : 0000000000000000
[ 6.858114] a5 : 0000000000000000 a6 : 0000000000000008 a7 : 0000000000000038
[ 6.859484] s2 : ff60000001e6c068 s3 : ff6000000108abb0 s4 : 0000000000000000
[ 6.860751] s5 : 0000000000001000 s6 : ffffffff8089dc40 s7 : ffffffff8089dc38
[ 6.862029] s8 : ffffffff8089dc30 s9 : ff60000000fdbe38 s10: 000000000000005e
[ 6.863304] s11: ffffffff80cc3510 t3 : ffffffff80d1112f t4 : ffffffff80d1112f
[ 6.864565] t5 : ffffffff80d11130 t6 : ff6000000181fa00
[ 6.865561] status: 0000000000000120 badaddr: 0000000000000020 cause: 000000000000000d
[ 6.868046] [<ffffffff8008dc94>] timens_commit+0x38/0x11a
[ 6.869089] [<ffffffff8008dde8>] timens_on_fork+0x72/0xb4
[ 6.870055] [<ffffffff80190096>] begin_new_exec+0x3c6/0x9f0
[ 6.871231] [<ffffffff801d826c>] load_elf_binary+0x628/0x1214
[ 6.872304] [<ffffffff8018ee7a>] bprm_execve+0x1f2/0x4e4
[ 6.873243] [<ffffffff8018f90c>] do_execveat_common+0x16e/0x1ee
[ 6.874258] [<ffffffff8018f9c8>] sys_execve+0x3c/0x48
[ 6.875162] [<ffffffff80003556>] ret_from_syscall+0x0/0x2
[ 6.877484] ---[ end trace 0000000000000000 ]---
This is because the mm->context.vdso_info is NULL in vfork case. From
another side, mm->context.vdso_info either points to vdso info
for RV64 or vdso info for compat, there's no need to bloat riscv's
mm_context_t, we can handle the difference when setup the additional
page for vdso. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/apic: Don't disable x2APIC if locked
The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC
(or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but
it disables the memory-mapped APIC interface in favor of one that uses
MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR.
The MMIO/xAPIC interface has some problems, most notably the APIC LEAK
[1]. This bug allows an attacker to use the APIC MMIO interface to
extract data from the SGX enclave.
Introduce support for a new feature that will allow the BIOS to lock
the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the
kernel tries to disable the APIC or revert to legacy APIC mode a GP
fault will occur.
Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle
the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by
preventing the kernel from trying to disable the x2APIC.
On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are
enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If
legacy APIC is required, then it SGX and TDX need to be disabled in the
BIOS.
[1]: https://aepicleak.com/aepicleak.pdf |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: qcom-adm: fix wrong calling convention for prep_slave_sg
The calling convention for pre_slave_sg is to return NULL on error and
provide an error log to the system. Qcom-adm instead provide error
pointer when an error occur. This indirectly cause kernel panic for
example for the nandc driver that checks only if the pointer returned by
device_prep_slave_sg is not NULL. Returning an error pointer makes nandc
think the device_prep_slave_sg function correctly completed and makes
the kernel panics later in the code.
While nandc is the one that makes the kernel crash, it was pointed out
that the real problem is qcom-adm not following calling convention for
that function.
To fix this, drop returning error pointer and return NULL with an error
log. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: do not run mt76u_status_worker if the device is not running
Fix the following NULL pointer dereference avoiding to run
mt76u_status_worker thread if the device is not running yet.
KASAN: null-ptr-deref in range
[0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 98 Comm: kworker/u2:2 Not tainted 5.14.0+ #78 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: mt76 mt76u_tx_status_data
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
mt76x02_send_tx_status+0x1d2/0xeb0
mt76x02_tx_status_data+0x8e/0xd0
mt76u_tx_status_data+0xe1/0x240
process_one_work+0x92b/0x1460
worker_thread+0x95/0xe00
kthread+0x3a1/0x480
ret_from_fork+0x1f/0x30
Modules linked in:
--[ end trace 8df5d20fc5040f65 ]--
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Moreover move stat_work schedule out of the for loop. |
| In the Linux kernel, the following vulnerability has been resolved:
ipu3-imgu: Fix NULL pointer dereference in imgu_subdev_set_selection()
Calling v4l2_subdev_get_try_crop() and v4l2_subdev_get_try_compose()
with a subdev state of NULL leads to a NULL pointer dereference. This
can currently happen in imgu_subdev_set_selection() when the state
passed in is NULL, as this method first gets pointers to both the "try"
and "active" states and only then decides which to use.
The same issue has been addressed for imgu_subdev_get_selection() with
commit 30d03a0de650 ("ipu3-imgu: Fix NULL pointer dereference in active
selection access"). However the issue still persists in
imgu_subdev_set_selection().
Therefore, apply a similar fix as done in the aforementioned commit to
imgu_subdev_set_selection(). To keep things a bit cleaner, introduce
helper functions for "crop" and "compose" access and use them in both
imgu_subdev_set_selection() and imgu_subdev_get_selection(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Prevent decl_tag from being referenced in func_proto arg
Syzkaller managed to hit another decl_tag issue:
btf_func_proto_check kernel/bpf/btf.c:4506 [inline]
btf_check_all_types kernel/bpf/btf.c:4734 [inline]
btf_parse_type_sec+0x1175/0x1980 kernel/bpf/btf.c:4763
btf_parse kernel/bpf/btf.c:5042 [inline]
btf_new_fd+0x65a/0xb00 kernel/bpf/btf.c:6709
bpf_btf_load+0x6f/0x90 kernel/bpf/syscall.c:4342
__sys_bpf+0x50a/0x6c0 kernel/bpf/syscall.c:5034
__do_sys_bpf kernel/bpf/syscall.c:5093 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5091 [inline]
__x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:5091
do_syscall_64+0x54/0x70 arch/x86/entry/common.c:48
This seems similar to commit ea68376c8bed ("bpf: prevent decl_tag from being
referenced in func_proto") but for the argument. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: VMX: Fix crash due to uninitialized current_vmcs
KVM enables 'Enlightened VMCS' and 'Enlightened MSR Bitmap' when running as
a nested hypervisor on top of Hyper-V. When MSR bitmap is updated,
evmcs_touch_msr_bitmap function uses current_vmcs per-cpu variable to mark
that the msr bitmap was changed.
vmx_vcpu_create() modifies the msr bitmap via vmx_disable_intercept_for_msr
-> vmx_msr_bitmap_l01_changed which in the end calls this function. The
function checks for current_vmcs if it is null but the check is
insufficient because current_vmcs is not initialized. Because of this, the
code might incorrectly write to the structure pointed by current_vmcs value
left by another task. Preemption is not disabled, the current task can be
preempted and moved to another CPU while current_vmcs is accessed multiple
times from evmcs_touch_msr_bitmap() which leads to crash.
The manipulation of MSR bitmaps by callers happens only for vmcs01 so the
solution is to use vmx->vmcs01.vmcs instead of current_vmcs.
BUG: kernel NULL pointer dereference, address: 0000000000000338
PGD 4e1775067 P4D 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
...
RIP: 0010:vmx_msr_bitmap_l01_changed+0x39/0x50 [kvm_intel]
...
Call Trace:
vmx_disable_intercept_for_msr+0x36/0x260 [kvm_intel]
vmx_vcpu_create+0xe6/0x540 [kvm_intel]
kvm_arch_vcpu_create+0x1d1/0x2e0 [kvm]
kvm_vm_ioctl_create_vcpu+0x178/0x430 [kvm]
kvm_vm_ioctl+0x53f/0x790 [kvm]
__x64_sys_ioctl+0x8a/0xc0
do_syscall_64+0x5c/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
spi: atmel-quadspi: Free resources even if runtime resume failed in .remove()
An early error exit in atmel_qspi_remove() doesn't prevent the device
unbind. So this results in an spi controller with an unbound parent
and unmapped register space (because devm_ioremap_resource() is undone).
So using the remaining spi controller probably results in an oops.
Instead unregister the controller unconditionally and only skip hardware
access and clk disable.
Also add a warning about resume failing and return zero unconditionally.
The latter has the only effect to suppress a less helpful error message by
the spi core. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: mcq: Fix &hwq->cq_lock deadlock issue
When ufshcd_err_handler() is executed, CQ event interrupt can enter waiting
for the same lock. This can happen in ufshcd_handle_mcq_cq_events() and
also in ufs_mtk_mcq_intr(). The following warning message will be generated
when &hwq->cq_lock is used in IRQ context with IRQ enabled. Use
ufshcd_mcq_poll_cqe_lock() with spin_lock_irqsave instead of spin_lock to
resolve the deadlock issue.
[name:lockdep&]WARNING: inconsistent lock state
[name:lockdep&]--------------------------------
[name:lockdep&]inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[name:lockdep&]kworker/u16:4/260 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffffff8028444600 (&hwq->cq_lock){?.-.}-{2:2}, at:
ufshcd_mcq_poll_cqe_lock+0x30/0xe0
[name:lockdep&]{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x17c/0x33c
_raw_spin_lock+0x5c/0x7c
ufshcd_mcq_poll_cqe_lock+0x30/0xe0
ufs_mtk_mcq_intr+0x60/0x1bc [ufs_mediatek_mod]
__handle_irq_event_percpu+0x140/0x3ec
handle_irq_event+0x50/0xd8
handle_fasteoi_irq+0x148/0x2b0
generic_handle_domain_irq+0x4c/0x6c
gic_handle_irq+0x58/0x134
call_on_irq_stack+0x40/0x74
do_interrupt_handler+0x84/0xe4
el1_interrupt+0x3c/0x78
<snip>
Possible unsafe locking scenario:
CPU0
----
lock(&hwq->cq_lock);
<Interrupt>
lock(&hwq->cq_lock);
*** DEADLOCK ***
2 locks held by kworker/u16:4/260:
[name:lockdep&]
stack backtrace:
CPU: 7 PID: 260 Comm: kworker/u16:4 Tainted: G S W OE
6.1.17-mainline-android14-2-g277223301adb #1
Workqueue: ufs_eh_wq_0 ufshcd_err_handler
Call trace:
dump_backtrace+0x10c/0x160
show_stack+0x20/0x30
dump_stack_lvl+0x98/0xd8
dump_stack+0x20/0x60
print_usage_bug+0x584/0x76c
mark_lock_irq+0x488/0x510
mark_lock+0x1ec/0x25c
__lock_acquire+0x4d8/0xffc
lock_acquire+0x17c/0x33c
_raw_spin_lock+0x5c/0x7c
ufshcd_mcq_poll_cqe_lock+0x30/0xe0
ufshcd_poll+0x68/0x1b0
ufshcd_transfer_req_compl+0x9c/0xc8
ufshcd_err_handler+0x3bc/0xea0
process_one_work+0x2f4/0x7e8
worker_thread+0x234/0x450
kthread+0x110/0x134
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
USB: usbtmc: Fix direction for 0-length ioctl control messages
The syzbot fuzzer found a problem in the usbtmc driver: When a user
submits an ioctl for a 0-length control transfer, the driver does not
check that the direction is set to OUT:
------------[ cut here ]------------
usb 3-1: BOGUS control dir, pipe 80000b80 doesn't match bRequestType fd
WARNING: CPU: 0 PID: 5100 at drivers/usb/core/urb.c:411 usb_submit_urb+0x14a7/0x1880 drivers/usb/core/urb.c:411
Modules linked in:
CPU: 0 PID: 5100 Comm: syz-executor428 Not tainted 6.3.0-syzkaller-12049-g58390c8ce1bd #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
RIP: 0010:usb_submit_urb+0x14a7/0x1880 drivers/usb/core/urb.c:411
Code: 7c 24 40 e8 1b 13 5c fb 48 8b 7c 24 40 e8 21 1d f0 fe 45 89 e8 44 89 f1 4c 89 e2 48 89 c6 48 c7 c7 e0 b5 fc 8a e8 19 c8 23 fb <0f> 0b e9 9f ee ff ff e8 ed 12 5c fb 0f b6 1d 12 8a 3c 08 31 ff 41
RSP: 0018:ffffc90003d2fb00 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8880789e9058 RCX: 0000000000000000
RDX: ffff888029593b80 RSI: ffffffff814c1447 RDI: 0000000000000001
RBP: ffff88801ea742f8 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: ffff88802915e528
R13: 00000000000000fd R14: 0000000080000b80 R15: ffff8880222b3100
FS: 0000555556ca63c0(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f9ef4d18150 CR3: 0000000073e5b000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
usb_start_wait_urb+0x101/0x4b0 drivers/usb/core/message.c:58
usb_internal_control_msg drivers/usb/core/message.c:102 [inline]
usb_control_msg+0x320/0x4a0 drivers/usb/core/message.c:153
usbtmc_ioctl_request drivers/usb/class/usbtmc.c:1954 [inline]
usbtmc_ioctl+0x1b3d/0x2840 drivers/usb/class/usbtmc.c:2097
To fix this, we must override the direction in the bRequestType field
of the control request structure when the length is 0. |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: free background tracker's queued work in btracker_destroy
Otherwise the kernel can BUG with:
[ 2245.426978] =============================================================================
[ 2245.435155] BUG bt_work (Tainted: G B W ): Objects remaining in bt_work on __kmem_cache_shutdown()
[ 2245.445233] -----------------------------------------------------------------------------
[ 2245.445233]
[ 2245.454879] Slab 0x00000000b0ce2b30 objects=64 used=2 fp=0x000000000a3c6a4e flags=0x17ffffc0000200(slab|node=0|zone=2|lastcpupid=0x1fffff)
[ 2245.467300] CPU: 7 PID: 10805 Comm: lvm Kdump: loaded Tainted: G B W 6.0.0-rc2 #19
[ 2245.476078] Hardware name: Dell Inc. PowerEdge R7525/0590KW, BIOS 2.5.6 10/06/2021
[ 2245.483646] Call Trace:
[ 2245.486100] <TASK>
[ 2245.488206] dump_stack_lvl+0x34/0x48
[ 2245.491878] slab_err+0x95/0xcd
[ 2245.495028] __kmem_cache_shutdown.cold+0x31/0x136
[ 2245.499821] kmem_cache_destroy+0x49/0x130
[ 2245.503928] btracker_destroy+0x12/0x20 [dm_cache]
[ 2245.508728] smq_destroy+0x15/0x60 [dm_cache_smq]
[ 2245.513435] dm_cache_policy_destroy+0x12/0x20 [dm_cache]
[ 2245.518834] destroy+0xc0/0x110 [dm_cache]
[ 2245.522933] dm_table_destroy+0x5c/0x120 [dm_mod]
[ 2245.527649] __dm_destroy+0x10e/0x1c0 [dm_mod]
[ 2245.532102] dev_remove+0x117/0x190 [dm_mod]
[ 2245.536384] ctl_ioctl+0x1a2/0x290 [dm_mod]
[ 2245.540579] dm_ctl_ioctl+0xa/0x20 [dm_mod]
[ 2245.544773] __x64_sys_ioctl+0x8a/0xc0
[ 2245.548524] do_syscall_64+0x5c/0x90
[ 2245.552104] ? syscall_exit_to_user_mode+0x12/0x30
[ 2245.556897] ? do_syscall_64+0x69/0x90
[ 2245.560648] ? do_syscall_64+0x69/0x90
[ 2245.564394] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 2245.569447] RIP: 0033:0x7fe52583ec6b
...
[ 2245.646771] ------------[ cut here ]------------
[ 2245.651395] kmem_cache_destroy bt_work: Slab cache still has objects when called from btracker_destroy+0x12/0x20 [dm_cache]
[ 2245.651408] WARNING: CPU: 7 PID: 10805 at mm/slab_common.c:478 kmem_cache_destroy+0x128/0x130
Found using: lvm2-testsuite --only "cache-single-split.sh"
Ben bisected and found that commit 0495e337b703 ("mm/slab_common:
Deleting kobject in kmem_cache_destroy() without holding
slab_mutex/cpu_hotplug_lock") first exposed dm-cache's incomplete
cleanup of its background tracker work objects. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: kill hooked chains to avoid loops on deduplicated compressed images
After heavily stressing EROFS with several images which include a
hand-crafted image of repeated patterns for more than 46 days, I found
two chains could be linked with each other almost simultaneously and
form a loop so that the entire loop won't be submitted. As a
consequence, the corresponding file pages will remain locked forever.
It can be _only_ observed on data-deduplicated compressed images.
For example, consider two chains with five pclusters in total:
Chain 1: 2->3->4->5 -- The tail pcluster is 5;
Chain 2: 5->1->2 -- The tail pcluster is 2.
Chain 2 could link to Chain 1 with pcluster 5; and Chain 1 could link
to Chain 2 at the same time with pcluster 2.
Since hooked chains are all linked locklessly now, I have no idea how
to simply avoid the race. Instead, let's avoid hooked chains completely
until I could work out a proper way to fix this and end users finally
tell us that it's needed to add it back.
Actually, this optimization can be found with multi-threaded workloads
(especially even more often on deduplicated compressed images), yet I'm
not sure about the overall system impacts of not having this compared
with implementation complexity. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-iocost: fix divide by 0 error in calc_lcoefs()
echo max of u64 to cost.model can cause divide by 0 error.
# echo 8:0 rbps=18446744073709551615 > /sys/fs/cgroup/io.cost.model
divide error: 0000 [#1] PREEMPT SMP
RIP: 0010:calc_lcoefs+0x4c/0xc0
Call Trace:
<TASK>
ioc_refresh_params+0x2b3/0x4f0
ioc_cost_model_write+0x3cb/0x4c0
? _copy_from_iter+0x6d/0x6c0
? kernfs_fop_write_iter+0xfc/0x270
cgroup_file_write+0xa0/0x200
kernfs_fop_write_iter+0x17d/0x270
vfs_write+0x414/0x620
ksys_write+0x73/0x160
__x64_sys_write+0x1e/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
calc_lcoefs() uses the input value of cost.model in DIV_ROUND_UP_ULL,
overflow would happen if bps plus IOC_PAGE_SIZE is greater than
ULLONG_MAX, it can cause divide by 0 error.
Fix the problem by setting basecost |
| In the Linux kernel, the following vulnerability has been resolved:
drm: bridge: dw_hdmi: fix connector access for scdc
Commit 5d844091f237 ("drm/scdc-helper: Pimp SCDC debugs") changed the scdc
interface to pick up an i2c adapter from a connector instead. However, in
the case of dw-hdmi, the wrong connector was being used to pass i2c adapter
information, since dw-hdmi's embedded connector structure is only populated
when the bridge attachment callback explicitly asks for it.
drm-meson is handling connector creation, so this won't happen, leading to
a NULL pointer dereference.
Fix it by having scdc functions access dw-hdmi's current connector pointer
instead, which is assigned during the bridge enablement stage.
[narmstrong: moved Fixes tag before first S-o-b and added Reported-by tag] |
| In the Linux kernel, the following vulnerability has been resolved:
perf tool x86: Fix perf_env memory leak
Found by leak sanitizer:
```
==1632594==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 21 byte(s) in 1 object(s) allocated from:
#0 0x7f2953a7077b in __interceptor_strdup ../../../../src/libsanitizer/asan/asan_interceptors.cpp:439
#1 0x556701d6fbbf in perf_env__read_cpuid util/env.c:369
#2 0x556701d70589 in perf_env__cpuid util/env.c:465
#3 0x55670204bba2 in x86__is_amd_cpu arch/x86/util/env.c:14
#4 0x5567020487a2 in arch__post_evsel_config arch/x86/util/evsel.c:83
#5 0x556701d8f78b in evsel__config util/evsel.c:1366
#6 0x556701ef5872 in evlist__config util/record.c:108
#7 0x556701cd6bcd in test__PERF_RECORD tests/perf-record.c:112
#8 0x556701cacd07 in run_test tests/builtin-test.c:236
#9 0x556701cacfac in test_and_print tests/builtin-test.c:265
#10 0x556701cadddb in __cmd_test tests/builtin-test.c:402
#11 0x556701caf2aa in cmd_test tests/builtin-test.c:559
#12 0x556701d3b557 in run_builtin tools/perf/perf.c:323
#13 0x556701d3bac8 in handle_internal_command tools/perf/perf.c:377
#14 0x556701d3be90 in run_argv tools/perf/perf.c:421
#15 0x556701d3c3f8 in main tools/perf/perf.c:537
#16 0x7f2952a46189 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58
SUMMARY: AddressSanitizer: 21 byte(s) leaked in 1 allocation(s).
``` |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88bd720
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.
However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.
When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().
Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up. However, we have
yet to get such a report, and only syzkaller stumbled on it. So, this
can be changed safely.
Note this does not change SOCK_SEQPACKET behaviour. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix null-ptr-deref in raid10_sync_request
init_resync() inits mempool and sets conf->have_replacemnt at the beginning
of sync, close_sync() frees the mempool when sync is completed.
After [1] recovery might be skipped and init_resync() is called but
close_sync() is not. null-ptr-deref occurs with r10bio->dev[i].repl_bio.
The following is one way to reproduce the issue.
1) create a array, wait for resync to complete, mddev->recovery_cp is set
to MaxSector.
2) recovery is woken and it is skipped. conf->have_replacement is set to
0 in init_resync(). close_sync() not called.
3) some io errors and rdev A is set to WantReplacement.
4) a new device is added and set to A's replacement.
5) recovery is woken, A have replacement, but conf->have_replacemnt is
0. r10bio->dev[i].repl_bio will not be alloced and null-ptr-deref
occurs.
Fix it by not calling init_resync() if recovery skipped.
[1] commit 7e83ccbecd60 ("md/raid10: Allow skipping recovery when clean arrays are assembled") |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: reject negative ifindex
Recent changes in net-next (commit 759ab1edb56c ("net: store netdevs
in an xarray")) refactored the handling of pre-assigned ifindexes
and let syzbot surface a latent problem in ovs. ovs does not validate
ifindex, making it possible to create netdev ports with negative
ifindex values. It's easy to repro with YNL:
$ ./cli.py --spec netlink/specs/ovs_datapath.yaml \
--do new \
--json '{"upcall-pid": 1, "name":"my-dp"}'
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
$ ip link show
-65536: some-port0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 7a:48:21:ad:0b:fb brd ff:ff:ff:ff:ff:ff
...
Validate the inputs. Now the second command correctly returns:
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
lib.ynl.NlError: Netlink error: Numerical result out of range
nl_len = 108 (92) nl_flags = 0x300 nl_type = 2
error: -34 extack: {'msg': 'integer out of range', 'unknown': [[type:4 len:36] b'\x0c\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x0c\x00\x03\x00\xff\xff\xff\x7f\x00\x00\x00\x00\x08\x00\x01\x00\x08\x00\x00\x00'], 'bad-attr': '.ifindex'}
Accept 0 since it used to be silently ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5-cache: fix a deadlock in r5l_exit_log()
Commit b13015af94cf ("md/raid5-cache: Clear conf->log after finishing
work") introduce a new problem:
// caller hold reconfig_mutex
r5l_exit_log
flush_work(&log->disable_writeback_work)
r5c_disable_writeback_async
wait_event
/*
* conf->log is not NULL, and mddev_trylock()
* will fail, wait_event() can never pass.
*/
conf->log = NULL
Fix this problem by setting 'config->log' to NULL before wake_up() as it
used to be, so that wait_event() from r5c_disable_writeback_async() can
exist. In the meantime, move forward md_unregister_thread() so that
null-ptr-deref this commit fixed can still be fixed. |
