| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: validate connector number in ucsi_notify_common()
The connector number extracted from CCI via UCSI_CCI_CONNECTOR() is a
7-bit field (0-127) that is used to index into the connector array in
ucsi_connector_change(). However, the array is only allocated for the
number of connectors reported by the device (typically 2-4 entries).
A malicious or malfunctioning device could report an out-of-range
connector number in the CCI, causing an out-of-bounds array access in
ucsi_connector_change().
Add a bounds check in ucsi_notify_common(), the central point where CCI
is parsed after arriving from hardware, so that bogus connector numbers
are rejected before they propagate further. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sched: act_csum: validate nested VLAN headers
tcf_csum_act() walks nested VLAN headers directly from skb->data when an
skb still carries in-payload VLAN tags. The current code reads
vlan->h_vlan_encapsulated_proto and then pulls VLAN_HLEN bytes without
first ensuring that the full VLAN header is present in the linear area.
If only part of an inner VLAN header is linearized, accessing
h_vlan_encapsulated_proto reads past the linear area, and the following
skb_pull(VLAN_HLEN) may violate skb invariants.
Fix this by requiring pskb_may_pull(skb, VLAN_HLEN) before accessing and
pulling each nested VLAN header. If the header still is not fully
available, drop the packet through the existing error path. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_multiport: validate range encoding in checkentry
ports_match_v1() treats any non-zero pflags entry as the start of a
port range and unconditionally consumes the next ports[] element as
the range end.
The checkentry path currently validates protocol, flags and count, but
it does not validate the range encoding itself. As a result, malformed
rules can mark the last slot as a range start or place two range starts
back to back, leaving ports_match_v1() to step past the last valid
ports[] element while interpreting the rule.
Reject malformed multiport v1 rules in checkentry by validating that
each range start has a following element and that the following element
is not itself marked as another range start. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: fireworks: bound device-supplied status before string array lookup
The status field in an EFW response is a 32-bit value supplied by the
firewire device. efr_status_names[] has 17 entries so a status value
outside that range goes off into the weeds when looking at the %s value.
Even worse, the status could return EFR_STATUS_INCOMPLETE which is
0x80000000, and is obviously not in that array of potential strings.
Fix this up by properly bounding the index against the array size and
printing "unknown" if it's not recognized. |
| The Symfony HtmlSanitizer component UrlSanitizer parses URLs differently from browsers, allowing the allowLinkHosts() and allowMediaHosts() checks to be bypassed for URLs without a well-formed authority, resulting in untrusted hosts being referenced in sanitized output in Symfony versions 6.1.x prior to 6.4.50, 7.x prior to 7.4.23, and 8.x prior to 8.1.11.
UrlSanitizer parses URLs with league/uri, which follows RFC 3986, while browsers follow the WHATWG URL standard. For URLs without a well-formed authority, such as http:evil.example, ///evil.example, or https://://evil.example/ the sanitizer finds no host, whereas browsers resolve them to evil.example. The guard added for CVE-2026-45066 missed the zero-slash form, and the host 0 was also skipped because PHP treats it as falsy.
This is exploitable when a host allow-list is combined with allowRelativeLinks(true) or allowRelativeMedias(true). The default configuration is not affected. |
| When a broker decodes a compressed record batch, the per-record decoder reads a declared body size from the decompressed stream and allocates a buffer of that size before validating it against the bytes available or any configured limit. The size is attacker-controlled, and the batch CRC does not constrain it, so a small (around 90-byte), CRC-valid compressed produce request can declare a body size of up to about 2 GiB and force the broker to attempt that allocation, raising OutOfMemoryError. The record size limit (max.message.bytes), the request size limit, and client/broker quotas bound only the compressed wire size, not the declared decompressed size.
Impact:
An authenticated principal with Write on a topic can crash broker request-handler threads (reached when a batch's codec differs from the topic's compression.type and records are re-encoded) and any consumer that fetches the record, denying service. On brokers started with -XX:+ExitOnOutOfMemoryError, a common hardening, a single crafted request terminates the broker JVM. More seriously, a crafted record is accepted at ingest and written to disk; when the log-cleaner later reads it on a compacted topic, the OutOfMemoryError (an Error, not an Exception) terminates the cleaner thread, which is not restarted. With the default of a single cleaner thread, log compaction then stops for the entire broker, including the internal __consumer_offsets and __transaction_state topics, and the condition persists across restarts until the offending record is removed. The impact is availability only; no data is disclosed or altered.
Mitigation:
Upgrade to Apache Kafka 4.2.2, 4.3.2, or 4.4.0, and set max.decompressed.message.bytes (at the broker and/or topic level) to a bounded value appropriate for your workload. Upgrading alone is not sufficient: for backward compatibility this configuration defaults to an effectively unlimited value (about 2 GiB), so a broker remains exposed until the limit is set. Choose a value at or slightly above the largest legitimate decompressed record your applications produce, and comfortably below the broker heap divided by the number of request-handler and cleaner threads. Until you can upgrade and configure the limit, restrict Write access to trusted producers; quotas and max.message.bytes do not mitigate this issue.
Resolution:
From Apache Kafka 4.2.2, 4.3.2, and 4.4.0: the broker validates a record's declared decompressed body size against max.decompressed.message.bytes before allocating, on the produce-validation, log-compaction, and timestamp-lookup paths, and rejects oversized or negative sizes with InvalidRecordException. Operators must set this configuration to a bounded value to be protected, as its default is effectively unlimited. |
| In the Linux kernel, the following vulnerability has been resolved:
module: Fix kernel panic when a symbol st_shndx is out of bounds
The module loader doesn't check for bounds of the ELF section index in
simplify_symbols():
for (i = 1; i < symsec->sh_size / sizeof(Elf_Sym); i++) {
const char *name = info->strtab + sym[i].st_name;
switch (sym[i].st_shndx) {
case SHN_COMMON:
[...]
default:
/* Divert to percpu allocation if a percpu var. */
if (sym[i].st_shndx == info->index.pcpu)
secbase = (unsigned long)mod_percpu(mod);
else
/** HERE --> **/ secbase = info->sechdrs[sym[i].st_shndx].sh_addr;
sym[i].st_value += secbase;
break;
}
}
A symbol with an out-of-bounds st_shndx value, for example 0xffff
(known as SHN_XINDEX or SHN_HIRESERVE), may cause a kernel panic:
BUG: unable to handle page fault for address: ...
RIP: 0010:simplify_symbols+0x2b2/0x480
...
Kernel panic - not syncing: Fatal exception
This can happen when module ELF is legitimately using SHN_XINDEX or
when it is corrupted.
Add a bounds check in simplify_symbols() to validate that st_shndx is
within the valid range before using it.
This issue was discovered due to a bug in llvm-objcopy, see relevant
discussion for details [1].
[1] https://lore.kernel.org/linux-modules/[email protected]/ |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Validate PDU length before reading SDU length in l2cap_ecred_data_rcv()
l2cap_ecred_data_rcv() reads the SDU length field from skb->data using
get_unaligned_le16() without first verifying that skb contains at least
L2CAP_SDULEN_SIZE (2) bytes. When skb->len is less than 2, this reads
past the valid data in the skb.
The ERTM reassembly path correctly calls pskb_may_pull() before reading
the SDU length (l2cap_reassemble_sdu, L2CAP_SAR_START case). Apply the
same validation to the Enhanced Credit Based Flow Control data path. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: clamp SCO altsetting table indices
btusb_work() maps the number of active SCO links to USB alternate
settings through a three-entry lookup table when CVSD traffic uses
transparent voice settings. The lookup currently indexes alts[] with
data->sco_num - 1 without first constraining sco_num to the number of
available table entries.
While the table only defines alternate settings for up to three SCO
links, data->sco_num comes from hci_conn_num() and is used directly.
Cap the lookup to the last table entry before indexing it so the
driver keeps selecting the highest supported alternate setting without
reading past alts[]. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: use netlink policy range checks
Replace manual range and mask validations with netlink policy
annotations in ctnetlink code paths, so that the netlink core rejects
invalid values early and can generate extack errors.
- CTA_PROTOINFO_TCP_STATE: reject values > TCP_CONNTRACK_SYN_SENT2 at
policy level, removing the manual >= TCP_CONNTRACK_MAX check.
- CTA_PROTOINFO_TCP_WSCALE_ORIGINAL/REPLY: reject values > TCP_MAX_WSCALE
(14). The normal TCP option parsing path already clamps to this value,
but the ctnetlink path accepted 0-255, causing undefined behavior when
used as a u32 shift count.
- CTA_FILTER_ORIG_FLAGS/REPLY_FLAGS: use NLA_POLICY_MASK with
CTA_FILTER_F_ALL, removing the manual mask checks.
- CTA_EXPECT_FLAGS: use NLA_POLICY_MASK with NF_CT_EXPECT_MASK, adding
a new mask define grouping all valid expect flags.
Extracted from a broader nf-next patch by Florian Westphal, scoped to
ctnetlink for the fixes tree. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/syscalls: Add spectre boundary for syscall dispatch table
The s390 syscall number is directly controlled by userspace, but does
not have an array_index_nospec() boundary to prevent access past the
syscall function pointer tables. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs: check contexts->nr before accessing contexts_arr[0]
Multiple sysfs command paths dereference contexts_arr[0] without first
verifying that kdamond->contexts->nr == 1. A user can set nr_contexts to
0 via sysfs while DAMON is running, causing NULL pointer dereferences.
In more detail, the issue can be triggered by privileged users like
below.
First, start DAMON and make contexts directory empty
(kdamond->contexts->nr == 0).
# damo start
# cd /sys/kernel/mm/damon/admin/kdamonds/0
# echo 0 > contexts/nr_contexts
Then, each of below commands will cause the NULL pointer dereference.
# echo update_schemes_stats > state
# echo update_schemes_tried_regions > state
# echo update_schemes_tried_bytes > state
# echo update_schemes_effective_quotas > state
# echo update_tuned_intervals > state
Guard all commands (except OFF) at the entry point of
damon_sysfs_handle_cmd(). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: replace BUG_ON with proper error handling in ext4_read_inline_folio
Replace BUG_ON() with proper error handling when inline data size
exceeds PAGE_SIZE. This prevents kernel panic and allows the system to
continue running while properly reporting the filesystem corruption.
The error is logged via ext4_error_inode(), the buffer head is released
to prevent memory leak, and -EFSCORRUPTED is returned to indicate
filesystem corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: x_tables: restrict xt_check_match/xt_check_target extensions for NFPROTO_ARP
Weiming Shi says:
xt_match and xt_target structs registered with NFPROTO_UNSPEC can be
loaded by any protocol family through nft_compat. When such a
match/target sets .hooks to restrict which hooks it may run on, the
bitmask uses NF_INET_* constants. This is only correct for families
whose hook layout matches NF_INET_*: IPv4, IPv6, INET, and bridge
all share the same five hooks (PRE_ROUTING ... POST_ROUTING).
ARP only has three hooks (IN=0, OUT=1, FORWARD=2) with different
semantics. Because NF_ARP_OUT == 1 == NF_INET_LOCAL_IN, the .hooks
validation silently passes for the wrong reasons, allowing matches to
run on ARP chains where the hook assumptions (e.g. state->in being
set on input hooks) do not hold. This leads to NULL pointer
dereferences; xt_devgroup is one concrete example:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000044: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000220-0x0000000000000227]
RIP: 0010:devgroup_mt+0xff/0x350
Call Trace:
<TASK>
nft_match_eval (net/netfilter/nft_compat.c:407)
nft_do_chain (net/netfilter/nf_tables_core.c:285)
nft_do_chain_arp (net/netfilter/nft_chain_filter.c:61)
nf_hook_slow (net/netfilter/core.c:623)
arp_xmit (net/ipv4/arp.c:666)
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
Fix it by restricting arptables to NFPROTO_ARP extensions only.
Note that arptables-legacy only supports:
- arpt_CLASSIFY
- arpt_mangle
- arpt_MARK
that provide explicit NFPROTO_ARP match/target declarations. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: cdc_ncm: add ndpoffset to NDP16 nframes bounds check
cdc_ncm_rx_verify_ndp16() validates that the NDP header and its DPE
entries fit within the skb. The first check correctly accounts for
ndpoffset:
if ((ndpoffset + sizeof(struct usb_cdc_ncm_ndp16)) > skb_in->len)
but the second check omits it:
if ((sizeof(struct usb_cdc_ncm_ndp16) +
ret * (sizeof(struct usb_cdc_ncm_dpe16))) > skb_in->len)
This validates the DPE array size against the total skb length as if
the NDP were at offset 0, rather than at ndpoffset. When the NDP is
placed near the end of the NTB (large wNdpIndex), the DPE entries can
extend past the skb data buffer even though the check passes.
cdc_ncm_rx_fixup() then reads out-of-bounds memory when iterating
the DPE array.
Add ndpoffset to the nframes bounds check and use struct_size_t() to
express the NDP-plus-DPE-array size more clearly. |
| In the Linux kernel, the following vulnerability has been resolved:
Squashfs: check metadata block offset is within range
Syzkaller reports a "general protection fault in squashfs_copy_data"
This is ultimately caused by a corrupted index look-up table, which
produces a negative metadata block offset.
This is subsequently passed to squashfs_copy_data (via
squashfs_read_metadata) where the negative offset causes an out of bounds
access.
The fix is to check that the offset is within range in
squashfs_read_metadata. This will trap this and other cases. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix incorrect buffer cleanup in gve_tx_clean_pending_packets for QPL
In DQ-QPL mode, gve_tx_clean_pending_packets() incorrectly uses the RDA
buffer cleanup path. It iterates num_bufs times and attempts to unmap
entries in the dma array.
This leads to two issues:
1. The dma array shares storage with tx_qpl_buf_ids (union).
Interpreting buffer IDs as DMA addresses results in attempting to
unmap incorrect memory locations.
2. num_bufs in QPL mode (counting 2K chunks) can significantly exceed
the size of the dma array, causing out-of-bounds access warnings
(trace below is how we noticed this issue).
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/drivers/net/ethernet/google/gve/gve_tx_dqo.c:178:5 index 18 is out of
range for type 'dma_addr_t[18]' (aka 'unsigned long long[18]')
Workqueue: gve gve_service_task [gve]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0xa0
__ubsan_handle_out_of_bounds+0xdc/0x110
gve_tx_stop_ring_dqo+0x182/0x200 [gve]
gve_close+0x1be/0x450 [gve]
gve_reset+0x99/0x120 [gve]
gve_service_task+0x61/0x100 [gve]
process_scheduled_works+0x1e9/0x380
Fix this by properly checking for QPL mode and delegating to
gve_free_tx_qpl_bufs() to reclaim the buffers. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kalmia: validate USB endpoints
The kalmia driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: Do not allow userspace to trivially triger kernel warnings
Userspace can either deliberately pass in the too small num_fences, or the
required number can legitimately grow between the two calls to the userq
wait ioctl. In both cases we do not want the emit the kernel warning
backtrace since nothing is wrong with the kernel and userspace will simply
get an errno reported back. So lets simply drop the WARN_ONs.
(cherry picked from commit 2c333ea579de6cc20ea7bc50e9595ef72863e65c) |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Use correct version for UAC3 header validation
The entry of the validators table for UAC3 AC header descriptor is
defined with the wrong protocol version UAC_VERSION_2, while it should
have been UAC_VERSION_3. This results in the validator never matching
for actual UAC3 devices (protocol == UAC_VERSION_3), causing their
header descriptors to bypass validation entirely. A malicious USB
device presenting a truncated UAC3 header could exploit this to cause
out-of-bounds reads when the driver later accesses unvalidated
descriptor fields.
The bug was introduced in the same commit as the recently fixed UAC3
feature unit sub-type typo, and appears to be from the same copy-paste
error when the UAC3 section was created from the UAC2 section. |
