| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/radeon: fix integer overflow in radeon_align_pitch()
radeon_align_pitch() has the same kind of overflow issue as the old
amdgpu helper: both the alignment round-up add and the final
'aligned * cpp' calculation can overflow signed int.
If that wraps, radeon_mode_dumb_create() can end up returning an
invalid pitch or creating a zero-sized dumb buffer.
Fix this by using check_add_overflow() for the alignment round-up and
check_mul_overflow() for the final pitch calculation, returning 0 on
overflow. Also reject zero pitch and size in
radeon_mode_dumb_create().
Found via AST-based call-graph analysis using sqry. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: cancel SSR work items during PCI shutdown
A reboot can crash the kernel if it overlaps with WLAN firmware crash
recovery (SSR). The crash is a NULL pointer dereference in the MHI teardown
path while freeing DMA-backed MHI contexts.
Simplified trace:
dma_free_attrs
mhi_deinit_dev_ctxt [mhi]
ath11k_pci_power_down [ath11k_pci]
ath11k_pci_shutdown [ath11k_pci]
device_shutdown
kernel_restart
On the host side, SSR is driven by the MHI RDDM callback, which queues
reset_work to perform device recovery. reset_work power-cycles the device
by calling ath11k_hif_power_down() followed by ath11k_hif_power_up(). The
power-down phase deinitializes MHI and frees DMA resources.
Shutdown/reboot runs fully asynchronously with this RDDM-driven SSR
recovery flow. As a result, the shutdown path
(ath11k_pci_shutdown() -> ath11k_pci_power_down()) can race with the SSR
recovery sequence.
Fix this by canceling SSR-related work items during PCI shutdown, marking
the device as unregistering, and serializing the RDDM callback path that
checks and queues reset_work. This ensures that no new SSR recovery work
can be queued once teardown has started, and that any in-flight recovery
work is fully synchronized before device power-down, preventing MHI
teardown and DMA resource freeing from running more than once.
Note: This issue only affects PCI/MHI-based devices. AHB-based ath11k
devices do not queue reset_work in normal SSR flows.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04866.5-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1 |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: Fix potential null-ptr-deref in vxlan_gro_prepare_receive().
udp_tunnel_sock_release() could set sk->sk_user_data to NULL
while vxlan_gro_prepare_receive() is running.
Let's check if rcu_dereference_sk_user_data() is NULL after
skb_gro_remcsum_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
OPP: Fix race between OPP addition and lookup
A race exists between dev_pm_opp_add_dynamic() and
dev_pm_opp_find_freq_exact():
CPU0 (add) CPU1 (lookup)
------------------------------- ------------------------------
_opp_add()
mutex_lock()
list_add(&new_opp->node, head)
mutex_unlock() _opp_table_find_key()
mutex_lock()
dev_pm_opp_get(opp)
kref_get()
mutex_unlock()
kref_init(&new_opp->kref)
dev_pm_opp_put()
kref_put_mutex()
The newly added OPP is inserted into the list before its kref is
initialized. A concurrent lookup can find this OPP and increment its
reference count while it is still uninitialized, leading to refcount
corruption and a potential premature free.
Fix this by initializing ->kref and ->opp_table before making the OPP
visible via list_add(). This ensures any concurrent lookup observes a
fully initialized object.
[ Viresh: Updated commit log ] |
| In the Linux kernel, the following vulnerability has been resolved:
dlm: fix add msg handle in send_queue ordered
In a benchmark scenario triggering a lot of requests that triggers a lot
of DLM messages on the network it can be that the mh->seq is not ordered
according the oldest seq number. This ordering is required by
dlm_receive_ack as "before(mh->seq, seq)" will stop to check for older
sequence numbers that are ordered in the tail of "node->send_queue".
The side effects of not having it correct ordered regarding
"before(mh->seq, seq)" are refcounting issues and use-after free.
I only was able to reproduce this issue in a experimental DLM branch
and a user space DLM benchmark that uses io_uring. After changing this I
don't experienced any refcounting with the sending buffer issues anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/mlx5: Fix transport-domain rollback and initialize lb mutex earlier
mlx5_ib_alloc_transport_domain() allocates a transport domain and then
may fail in mlx5_ib_enable_lb(). In that case, the allocated TD is leaked.
Fix this by deallocating the TD when mlx5_ib_enable_lb() returns an
error. Also return 0 explicitly in the no-loopback-capability success
branch, and move dev->lb.mutex initialization to mlx5_ib_stage_init_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Bound synthetic-field strings with seq_buf
The synthetic field helpers build a prefixed synthetic variable name and
a generated hist command in fixed MAX_FILTER_STR_VAL buffers. The
current code appends those strings with raw strcat(), so long key lists,
field names, or saved filters can run past the end of the staging
buffers.
Build both strings with seq_buf and propagate -E2BIG if either the
synthetic variable name or the generated command exceeds
MAX_FILTER_STR_VAL. This keeps the existing tracing-side limit while
using the helper intended for bounded command construction.
[ sdr: Moved struct seq_buf *s for upside-down x-mas tree formatting ] |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix log flood after cmd_mbox failure
hns_roce_cmd_mbox() is the command interface between driver and
hardware. When hardware is abnormal, the unlimited error printings
after hns_roce_cmd_mbox() failure will cause log flood and even
system crash.
Replace ibdev_err() and ibdev_warn() with their ratelimited versions
in the error handling path after hns_roce_cmd_mbox() (and its wrappers
hns_roce_create_hw_ctx/hns_roce_destroy_hw_ctx) fails. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: oss: Fix UAF at handling events with embedded SysEx data
The OSS sequencer processes the input MIDI bytes into a sequencer
event to be dispatched later (in snd_seq_oss_midi_putc() called from
snd_seq_oss_process_event()). When it's a SysEx data, the event
record contains data.ext.ptr pointer to the original SysEx bytes, and
the referred data is copied into the pool afterwards at dispatching.
The problem is that, if the sequencer port gets closed concurrently
before the dispatch, the OSS sequencer core also releases the
resources (in snd_seq_oss_midi_check_exit_port()), while the pending
event may hold a stale pointer, eventually leading to a UAF at a later
dispatch.
Fortunately, there is already a refcounting mechanism (snd_use_lock_t)
for the OSS MIDI device access, and for addressing the issue above, we
just need to extend the refcount until the event gets dispatched.
This patch extends snd_seq_oss_process_event() to give back the
refcount object, which is in turn released after calling the sequencer
dispatcher with the given event in the caller side.
According to the original report, KASAN report as below:
KASAN slab-use-after-free in snd_seq_event_dup+0x40c/0x470
RIP: 0033:0x7f2cb66a6340
Read of size 6
Call trace:
dump_stack_lvl+0x73/0xb0 (?:?)
print_report+0xd1/0x650 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x1a7/0x340 (?:?)
kasan_complete_mode_report_info+0x64/0x200 (?:?)
kasan_report+0xf7/0x130 (?:?)
snd_seq_event_dup+0x40c/0x470 (?:?)
kasan_check_range+0x10c/0x1c0 (?:?)
__asan_memcpy+0x27/0x70 (?:?)
snd_seq_event_dup+0x9/0x470 (?:?)
snd_seq_client_enqueue_event+0x139/0x240 (?:?)
_raw_spin_unlock_irqrestore+0x4b/0x60 (?:?)
snd_seq_kernel_client_enqueue+0x102/0x120 (?:?)
snd_seq_oss_write+0x416/0x4e0 (?:?)
apparmor_file_permission+0x20/0x30 (?:?)
odev_write+0x3b/0x60 (?:?)
vfs_write+0x1ce/0x850 (?:?)
lock_release+0xc8/0x2a0 (?:?)
__kasan_check_write+0x18/0x20 (?:?)
__mutex_unlock_slowpath+0x129/0x510 (?:?)
ksys_write+0xe1/0x180 (?:?)
mutex_unlock+0x16/0x20 (?:?)
odev_ioctl+0x65/0xc0 (?:?)
__x64_sys_write+0x46/0x60 (?:?)
x64_sys_call+0x7d/0x20d0 (?:?)
do_syscall_64+0xc1/0x360 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-tcp: fix page fragment cache leak in error path
In nvmet_tcp_alloc_queue(), when a connection is closed during the
allocation process (e.g., nvmet_tcp_set_queue_sock() returns -ENOTCONN),
the error handling jumps to out_destroy_sq and then to out_ida_remove
without draining the page fragment cache.
Although nvmet_tcp_free_cmd() is called in some error paths to release
individual page fragments, the underlying page cache reference held by
queue->pf_cache is never released. The first allocation using pf_cache
is the call to nvmet_tcp_alloc_cmd() for queue->connect, which happens
after ida_alloc() returns successfully. This results in a page leak each
time a connection fails during allocation, which could lead to memory
exhaustion over time if connections are repeatedly opened and closed.
Fix this by calling page_frag_cache_drain() before freeing the queue
structure in the out_ida_remove label. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost: fix vhost_get_avail_idx for a non empty ring
vhost_get_avail_idx is supposed to report whether it has updated
vq->avail_idx. Instead, it returns whether all entries have been
consumed, which is usually the same. But not always - in
drivers/vhost/net.c and when mergeable buffers have been enabled, the
driver checks whether the combined entries are big enough to store an
incoming packet. If not, the driver re-enables notifications with
available entries still in the ring. The incorrect return value from
vhost_get_avail_idx propagates through vhost_enable_notify and causes
the host to livelock if the guest is not making progress, as vhost will
immediately disable notifications and retry using the available entries.
This goes back to commit d3bb267bbdcb ("vhost: cache avail index in
vhost_enable_notify()") which changed vhost_enable_notify() to compare
the freshly read avail index against vq->last_avail_idx instead of the
previously cached vq->avail_idx. Commit 7ad472397667 ("vhost: move
smp_rmb() into vhost_get_avail_idx()") then carried over the same
comparison when refactoring vhost_enable_notify() to call the unified
vhost_get_avail_idx().
The obvious fix is to make vhost_get_avail_idx do what the comment
says it does and report whether new entries have been added. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: validate fast symlink target during inode read
ocfs2_validate_inode_block() already rejects several inconsistent
self-contained dinodes before they are exposed to the rest of the
filesystem. Fast symlinks need the same treatment.
A zero-cluster symlink is treated as a fast symlink and later read through
page_get_link() and ocfs2_fast_symlink_read_folio(). That path uses
strnlen() on the inline payload and then copies len + 1 bytes into the
folio. If a corrupt dinode stores an i_size that does not fit the inline
area or omits the terminating NUL at i_size, that copy reads past the end
of the inode block buffer.
Reject zero-cluster symlink dinodes whose i_size exceeds the inline
fast-symlink capacity or whose inline payload is not NUL-terminated
exactly at i_size when the inode block is validated. This keeps malformed
fast symlinks from reaching the read path.
Validation reproduced this kernel report:
KASAN use-after-free in ocfs2_fast_symlink_read_folio+0x12c/0x1f0
RIP: 0033:0x7f5c6d859aa7
Read of size 3905
Call trace:
dump_stack_lvl+0x66/0xa0 (?:?)
print_report+0xce/0x630 (?:?)
ocfs2_fast_symlink_read_folio+0x12c/0x1f0 (fs/ocfs2/inode.c:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x19f/0x330 (?:?)
kasan_report+0xe0/0x110 (?:?)
kasan_check_range+0x105/0x1b0 (?:?)
__asan_memcpy+0x23/0x60 (?:?)
filemap_read_folio+0x27/0xe0 (?:?)
filemap_read_folio+0x35/0xe0 (?:?)
do_read_cache_folio+0x138/0x230 (?:?)
__page_get_link+0x26/0x110 (?:?)
page_get_link+0x2e/0x70 (?:?)
vfs_readlink+0x15e/0x250 (?:?)
touch_atime+0x4d/0x370 (?:?)
do_readlinkat+0x186/0x200 (?:?)
do_user_addr_fault+0x65a/0x890 (?:?)
__x64_sys_readlink+0x46/0x60 (?:?)
do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: cttimeout: detach dataplane timeout policy and repurpose refcount
Add a refcount for struct nf_ct_timeout which is used by ct extension to
set the custom ct timeout policy, this tells us that the ct timeout is
being used by a conntrack entry. When the last conntrack entry drops the
refcount on the ct timeout, the ct timeout is released.
Remove the refcount for control plane which controls if the ruleset
refers to the timeout policy. After this update, it is possible to
remove the ct timeout policy from nfnetlink_cttimeout immediately.
This is for simplicity not to handle two refcounts on a single object.
Remove nf_queue_nf_hook_drop(): a packet sitting in nfqueue will just
hold a reference to the nf_ct_timeout object until packet is reinjected,
since this is part of the ct extension, this will be released by the
time the conntrack is freed.
nf_ct_untimeout() is still called to clean up in a best effort basis:
the ct timeout on existing entries gets removed when the ct timeout goes
away, but as long as the iptables ruleset still refers to the ct timeout
through a template, new conntracks may keep attaching it and extend its
lifetime until the rule is removed.
nf_ct_untimeout() is not called anymore from module removal path, this
is unlikely to find timeouts give module refcount is bumped, and the new
refcount already tracks the ct timeout policy use so it is released when
unused. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Fix endpoint/socket association handling
Disassociating a socket from an endpoint via siw_socket_disassoc() may
release the last reference on that endpoint and free it. Therefore, don't
clear the endpoints socket pointer after calling that function, but
within.
This fixes a:
BUG: KASAN: slab-use-after-free in siw_cm_work_handler (drivers/infiniband/sw/siw/siw_cm.c:1053 drivers/infiniband/sw/siw/siw_cm.c:1075)
which occurred after processing a malformed MPA request during connection
establishment, causing the new endpoint to be closed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wcn36xx: fix heap overflow from oversized firmware HAL response
The firmware response dispatcher copies all synchronous HAL responses
into the 4096-byte hal_buf without validating the response length. A
response exceeding WCN36XX_HAL_BUF_SIZE causes a heap buffer overflow
with firmware-controlled content.
Add a bounds check on the response length. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Clear variable event pointer on read
snd_seq_read() copies a queued variable-length event header to userspace
before expanding the payload. Queued variable-length events use
SNDRV_SEQ_EXT_CHAINED internally, and data.ext.ptr points at the first
extension cell.
The read side strips SNDRV_SEQ_EXT_* bits from data.ext.len before the
copy, but it leaves data.ext.ptr untouched. A userspace sequencer client
can therefore write a direct variable event to itself and read back the
extension-cell kernel address from the returned header.
Clear the temporary header pointer before copy_to_user(). The original
queued event remains unchanged and is still passed to
snd_seq_expand_var_event(), so payload expansion keeps using the
internal chain. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject sleepable BPF_LSM_CGROUP programs at load time
The cgroup shim runs under rcu_read_lock_dont_migrate(), so we should
not attach any sleepable BPF programs there. Add support to the verifier
to explicitly reject attempts to load sleepable BPF programs destined
for LSM cgroup attachment.
Without this, we get the following splat from a BPF_LSM_CGROUP
program marked BPF_F_SLEEPABLE attached to file_open when it calls
bpf_get_dentry_xattr():
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:1567
in_atomic(): 0, irqs_disabled(): 0, non_block: 0, pid: 34317, name: load
preempt_count: 0, expected: 0
RCU nest depth: 2, expected: 0
Call Trace:
down_read+0x76/0x480
ext4_xattr_get+0x11f/0x700
__vfs_getxattr+0xf0/0x150
bpf_get_dentry_xattr+0xbb/0xf0
bpf_prog_e76a298dac9218c6_test_open+0x6a/0x85
__cgroup_bpf_run_lsm_current+0x326/0x840
bpf_trampoline_6442534646+0x62/0x14d
security_file_open+0x34/0x60
do_dentry_open+0x340/0x1260
vfs_open+0x7a/0x440
path_openat+0x1bac/0x30a0
libbpf provides a .s named section variant for every sleepable
program type except lsm_cgroup, reflecting that per-cgroup LSM programs
are intended to only run in a non-sleepable context.
The above splat was obtained by bypassing libbpf by using bpf(2)
directly. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix deadlock cloning inline extent when using flushoncommit
In commit b48c980b6a7e ("btrfs: fix deadlock between reflink and
transaction commit when using flushoncommit") a deadlock was fixed
between reflinks and transaction commits when the fs is mounted with the
flushoncommit option. This happened when we had to copy an inline extent's
data to the destination file. However the issue was fixed only for the
case where the destination offset is 0, it missed the case when the offset
is greater than zero.
Fix this by ensuring we get i_size update whenever we copied an inline
extent's data into the destination file.
Syzbot reported this with the following trace:
INFO: task kworker/u8:3:57 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:3 state:D stack:21600 pid:57 tgid:57 ppid:2 task_flags:0x4208160 flags:0x00080000
Workqueue: writeback wb_workfn (flush-btrfs-129)
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5402 [inline]
__schedule+0x16f9/0x5500 kernel/sched/core.c:7204
__schedule_loop kernel/sched/core.c:7283 [inline]
schedule+0x164/0x360 kernel/sched/core.c:7298
wait_extent_bit fs/btrfs/extent-io-tree.c:905 [inline]
btrfs_lock_extent_bits+0x59c/0x700 fs/btrfs/extent-io-tree.c:2008
btrfs_lock_extent fs/btrfs/extent-io-tree.h:152 [inline]
btrfs_invalidate_folio+0x440/0xc00 fs/btrfs/inode.c:7718
extent_writepage fs/btrfs/extent_io.c:1848 [inline]
extent_write_cache_pages fs/btrfs/extent_io.c:2552 [inline]
btrfs_writepages+0x12f3/0x2410 fs/btrfs/extent_io.c:2684
do_writepages+0x32e/0x550 mm/page-writeback.c:2571
__writeback_single_inode+0x133/0x10e0 fs/fs-writeback.c:1764
writeback_sb_inodes+0x97f/0x1980 fs/fs-writeback.c:2056
wb_writeback+0x445/0xb00 fs/fs-writeback.c:2241
wb_do_writeback fs/fs-writeback.c:2388 [inline]
wb_workfn+0x3fd/0xf20 fs/fs-writeback.c:2428
process_one_work+0x98b/0x1630 kernel/workqueue.c:3318
process_scheduled_works kernel/workqueue.c:3401 [inline]
worker_thread+0xb49/0x1140 kernel/workqueue.c:3482
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
INFO: task syz.0.145:8523 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.0.145 state:D stack:22752 pid:8523 tgid:8522 ppid:5850 task_flags:0x400140 flags:0x00080002
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5402 [inline]
__schedule+0x16f9/0x5500 kernel/sched/core.c:7204
__schedule_loop kernel/sched/core.c:7283 [inline]
schedule+0x164/0x360 kernel/sched/core.c:7298
wb_wait_for_completion+0x3e8/0x790 fs/fs-writeback.c:227
__writeback_inodes_sb_nr+0x24c/0x2d0 fs/fs-writeback.c:2847
try_to_writeback_inodes_sb+0x9a/0xc0 fs/fs-writeback.c:2895
btrfs_start_delalloc_flush fs/btrfs/transaction.c:2182 [inline]
btrfs_commit_transaction+0x813/0x2fc0 fs/btrfs/transaction.c:2371
btrfs_sync_file+0xdf4/0x1230 fs/btrfs/file.c:1822
generic_write_sync include/linux/fs.h:2663 [inline]
btrfs_do_write_iter+0x6a9/0x840 fs/btrfs/file.c:1473
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x629/0xba0 fs/read_write.c:688
ksys_write+0x156/0x270 fs/read_write.c:740
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x15f/0x560 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f5a0bdece59
RSP: 002b:00007f5a0b446028 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007f5a0c065fa0 RCX: 00007f5a0bdece59
RDX: 000000000000029f RSI: 0000200000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ixgbe: do not configure xps for XDP queues
netif_set_xps_queue() should not be called for an XDP Tx queue, since such
queues are not netdev-exposed. On systems with number of CPUs >=64, on E610
adapter, netdev is configured with maximum number queue pairs being 63
(due to MSI-X assignment), but configuring XDP results in 64 XDP queues.
So, during XDP program load, when netif_set_xps_queue() is called for the
last XDP queue, we get a WARNING with a call trace and KASAN report
afterwards (if enabled).
[ 2012.699800] WARNING: net/core/dev.c:2854 at __netif_set_xps_queue+0x116a/0x1e40, CPU#36: xdpsock/103668
[...]
[ 2012.700029] RIP: 0010:__netif_set_xps_queue+0x116a/0x1e40
[ 2012.700035] Code: b6 34 06 48 89 f8 83 e0 07 83 c0 01 40 38 f0 7c 09 40 84 f6 0f 85 03 0a 00 00 0f b7 44 24 40 66 43 89 44 6a 18 e9 01 fb ff ff <0f> 0b e9 f2 ee ff ff 44 8b 44 24 44 45 85 c0 74 50 4d 85 e4 0f 84
[ 2012.700040] RSP: 0018:ffff8882369aeb28 EFLAGS: 00010246
[ 2012.700046] RAX: 0000000000000000 RBX: 000000000000003f RCX: 0000000000000000
[ 2012.700050] RDX: 1ffff1111da3d891 RSI: ffff888120e34250 RDI: ffff8888ed1ec488
[ 2012.700054] RBP: ffff888913281560 R08: 0000000000000000 R09: ffff8888ed1ec000
[ 2012.700058] R10: ffff8888a2e83180 R11: 0000000000000000 R12: 0000000000007fa8
[ 2012.700061] R13: 000000000000003f R14: ffff888120e34854 R15: ffff8889132817c8
[ 2012.700065] FS: 00007fc8ea9ff740(0000) GS:ffff88884cefe000(0000) knlGS:0000000000000000
[ 2012.700069] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2012.700073] CR2: 00007f81c8000020 CR3: 00000002299f8006 CR4: 00000000007726f0
[ 2012.700077] PKRU: 55555554
[ 2012.700080] Call Trace:
[ 2012.700084] <TASK>
[ 2012.700087] ? ktime_get+0x61/0x150
[ 2012.700097] ? usleep_range_state+0x133/0x1b0
[ 2012.700108] ? __pfx_usleep_range_state+0x10/0x10
[ 2012.700114] netif_set_xps_queue+0x31/0x50
[ 2012.700119] ixgbe_configure_tx_ring+0x472/0x920 [ixgbe]
[...]
[ 2012.700486] ixgbe_xdp+0x38f/0x750 [ixgbe]
[...]
[ 2012.701094] BUG: KASAN: slab-out-of-bounds in __netif_set_xps_queue+0x1ac5/0x1e40
[ 2012.701100] Write of size 4 at addr ffff88888d43cff8 by task xdpsock/103668
Skip XPS configuration for XDP Tx queues. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix kernel BUG in ext4_write_inline_data_end
When the data=journal mount option is used, the ext4_journalled_write_end()
function incorrectly calls ext4_write_inline_data_end() without checking
if the EXT4_STATE_MAY_INLINE_DATA flag is still set on the inode.
If a previous attempt to convert the inline data to an extent failed (e.g.
due to ENOSPC), the EXT4_STATE_MAY_INLINE_DATA flag is cleared, but
the EXT4_INODE_INLINE_DATA flag remains set. In this scenario, the next
call to ext4_write_begin() will not prepare the inline data xattr for
writing, but ext4_journalled_write_end() will incorrectly attempt to write
to it, triggering a BUG_ON(pos + len > EXT4_I(inode)->i_inline_size) in
ext4_write_inline_data() since i_inline_size was not expanded.
Fix this by ensuring that ext4_journalled_write_end() only calls
ext4_write_inline_data_end() if the EXT4_STATE_MAY_INLINE_DATA flag is
set, mirroring the behavior of ext4_write_end() and ext4_da_write_end(). |
