| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()
In 'wlc_phy_iqcal_gainparams_nphy()', add gain range check to WARN()
instead of possible out-of-bounds 'tbl_iqcal_gainparams_nphy' access.
Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: check local interfaces before deleting sdata list
syzkaller reported a corrupted list in ieee802154_if_remove. [1]
Remove an IEEE 802.15.4 network interface after unregister an IEEE 802.15.4
hardware device from the system.
CPU0 CPU1
==== ====
genl_family_rcv_msg_doit ieee802154_unregister_hw
ieee802154_del_iface ieee802154_remove_interfaces
rdev_del_virtual_intf_deprecated list_del(&sdata->list)
ieee802154_if_remove
list_del_rcu
The net device has been unregistered, since the rcu grace period,
unregistration must be run before ieee802154_if_remove.
To avoid this issue, add a check for local->interfaces before deleting
sdata list.
[1]
kernel BUG at lib/list_debug.c:58!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 UID: 0 PID: 6277 Comm: syz-executor157 Not tainted 6.12.0-rc6-syzkaller-00005-g557329bcecc2 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:__list_del_entry_valid_or_report+0xf4/0x140 lib/list_debug.c:56
Code: e8 a1 7e 00 07 90 0f 0b 48 c7 c7 e0 37 60 8c 4c 89 fe e8 8f 7e 00 07 90 0f 0b 48 c7 c7 40 38 60 8c 4c 89 fe e8 7d 7e 00 07 90 <0f> 0b 48 c7 c7 a0 38 60 8c 4c 89 fe e8 6b 7e 00 07 90 0f 0b 48 c7
RSP: 0018:ffffc9000490f3d0 EFLAGS: 00010246
RAX: 000000000000004e RBX: dead000000000122 RCX: d211eee56bb28d00
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff88805b278dd8 R08: ffffffff8174a12c R09: 1ffffffff2852f0d
R10: dffffc0000000000 R11: fffffbfff2852f0e R12: dffffc0000000000
R13: dffffc0000000000 R14: dead000000000100 R15: ffff88805b278cc0
FS: 0000555572f94380(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056262e4a3000 CR3: 0000000078496000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__list_del_entry_valid include/linux/list.h:124 [inline]
__list_del_entry include/linux/list.h:215 [inline]
list_del_rcu include/linux/rculist.h:157 [inline]
ieee802154_if_remove+0x86/0x1e0 net/mac802154/iface.c:687
rdev_del_virtual_intf_deprecated net/ieee802154/rdev-ops.h:24 [inline]
ieee802154_del_iface+0x2c0/0x5c0 net/ieee802154/nl-phy.c:323
genl_family_rcv_msg_doit net/netlink/genetlink.c:1115 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0xb14/0xec0 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2551
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1331 [inline]
netlink_unicast+0x7f6/0x990 net/netlink/af_netlink.c:1357
netlink_sendmsg+0x8e4/0xcb0 net/netlink/af_netlink.c:1901
sock_sendmsg_nosec net/socket.c:729 [inline]
__sock_sendmsg+0x221/0x270 net/socket.c:744
____sys_sendmsg+0x52a/0x7e0 net/socket.c:2607
___sys_sendmsg net/socket.c:2661 [inline]
__sys_sendmsg+0x292/0x380 net/socket.c:2690
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| Integer overflows in memory allocation in Das U-Boot before 2025.01-rc1 occur for a crafted squashfs filesystem via sbrk, via request2size, or because ptrdiff_t is mishandled on x86_64. |
| An integer overflow in ext4fs_read_symlink in Das U-Boot before 2025.01-rc1 occurs for zalloc (adding one to an le32 variable) via a crafted ext4 filesystem with an inode size of 0xffffffff, resulting in a malloc of zero and resultant memory overwrite. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vboxvideo: Replace fake VLA at end of vbva_mouse_pointer_shape with real VLA
Replace the fake VLA at end of the vbva_mouse_pointer_shape shape with
a real VLA to fix a "memcpy: detected field-spanning write error" warning:
[ 13.319813] memcpy: detected field-spanning write (size 16896) of single field "p->data" at drivers/gpu/drm/vboxvideo/hgsmi_base.c:154 (size 4)
[ 13.319841] WARNING: CPU: 0 PID: 1105 at drivers/gpu/drm/vboxvideo/hgsmi_base.c:154 hgsmi_update_pointer_shape+0x192/0x1c0 [vboxvideo]
[ 13.320038] Call Trace:
[ 13.320173] hgsmi_update_pointer_shape [vboxvideo]
[ 13.320184] vbox_cursor_atomic_update [vboxvideo]
Note as mentioned in the added comment it seems the original length
calculation for the allocated and send hgsmi buffer is 4 bytes too large.
Changing this is not the goal of this patch, so this behavior is kept. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: dax: fix overflowing extents beyond inode size when partially writing
The dax_iomap_rw() does two things in each iteration: map written blocks
and copy user data to blocks. If the process is killed by user(See signal
handling in dax_iomap_iter()), the copied data will be returned and added
on inode size, which means that the length of written extents may exceed
the inode size, then fsck will fail. An example is given as:
dd if=/dev/urandom of=file bs=4M count=1
dax_iomap_rw
iomap_iter // round 1
ext4_iomap_begin
ext4_iomap_alloc // allocate 0~2M extents(written flag)
dax_iomap_iter // copy 2M data
iomap_iter // round 2
iomap_iter_advance
iter->pos += iter->processed // iter->pos = 2M
ext4_iomap_begin
ext4_iomap_alloc // allocate 2~4M extents(written flag)
dax_iomap_iter
fatal_signal_pending
done = iter->pos - iocb->ki_pos // done = 2M
ext4_handle_inode_extension
ext4_update_inode_size // inode size = 2M
fsck reports: Inode 13, i_size is 2097152, should be 4194304. Fix?
Fix the problem by truncating extents if the written length is smaller
than expected. |
| Issue summary: Use of the low-level GF(2^m) elliptic curve APIs with untrusted
explicit values for the field polynomial can lead to out-of-bounds memory reads
or writes.
Impact summary: Out of bound memory writes can lead to an application crash or
even a possibility of a remote code execution, however, in all the protocols
involving Elliptic Curve Cryptography that we're aware of, either only "named
curves" are supported, or, if explicit curve parameters are supported, they
specify an X9.62 encoding of binary (GF(2^m)) curves that can't represent
problematic input values. Thus the likelihood of existence of a vulnerable
application is low.
In particular, the X9.62 encoding is used for ECC keys in X.509 certificates,
so problematic inputs cannot occur in the context of processing X.509
certificates. Any problematic use-cases would have to be using an "exotic"
curve encoding.
The affected APIs include: EC_GROUP_new_curve_GF2m(), EC_GROUP_new_from_params(),
and various supporting BN_GF2m_*() functions.
Applications working with "exotic" explicit binary (GF(2^m)) curve parameters,
that make it possible to represent invalid field polynomials with a zero
constant term, via the above or similar APIs, may terminate abruptly as a
result of reading or writing outside of array bounds. Remote code execution
cannot easily be ruled out.
The FIPS modules in 3.3, 3.2, 3.1 and 3.0 are not affected by this issue. |
| Issue summary: Calling the OpenSSL API function SSL_select_next_proto with an
empty supported client protocols buffer may cause a crash or memory contents to
be sent to the peer.
Impact summary: A buffer overread can have a range of potential consequences
such as unexpected application beahviour or a crash. In particular this issue
could result in up to 255 bytes of arbitrary private data from memory being sent
to the peer leading to a loss of confidentiality. However, only applications
that directly call the SSL_select_next_proto function with a 0 length list of
supported client protocols are affected by this issue. This would normally never
be a valid scenario and is typically not under attacker control but may occur by
accident in the case of a configuration or programming error in the calling
application.
The OpenSSL API function SSL_select_next_proto is typically used by TLS
applications that support ALPN (Application Layer Protocol Negotiation) or NPN
(Next Protocol Negotiation). NPN is older, was never standardised and
is deprecated in favour of ALPN. We believe that ALPN is significantly more
widely deployed than NPN. The SSL_select_next_proto function accepts a list of
protocols from the server and a list of protocols from the client and returns
the first protocol that appears in the server list that also appears in the
client list. In the case of no overlap between the two lists it returns the
first item in the client list. In either case it will signal whether an overlap
between the two lists was found. In the case where SSL_select_next_proto is
called with a zero length client list it fails to notice this condition and
returns the memory immediately following the client list pointer (and reports
that there was no overlap in the lists).
This function is typically called from a server side application callback for
ALPN or a client side application callback for NPN. In the case of ALPN the list
of protocols supplied by the client is guaranteed by libssl to never be zero in
length. The list of server protocols comes from the application and should never
normally be expected to be of zero length. In this case if the
SSL_select_next_proto function has been called as expected (with the list
supplied by the client passed in the client/client_len parameters), then the
application will not be vulnerable to this issue. If the application has
accidentally been configured with a zero length server list, and has
accidentally passed that zero length server list in the client/client_len
parameters, and has additionally failed to correctly handle a "no overlap"
response (which would normally result in a handshake failure in ALPN) then it
will be vulnerable to this problem.
In the case of NPN, the protocol permits the client to opportunistically select
a protocol when there is no overlap. OpenSSL returns the first client protocol
in the no overlap case in support of this. The list of client protocols comes
from the application and should never normally be expected to be of zero length.
However if the SSL_select_next_proto function is accidentally called with a
client_len of 0 then an invalid memory pointer will be returned instead. If the
application uses this output as the opportunistic protocol then the loss of
confidentiality will occur.
This issue has been assessed as Low severity because applications are most
likely to be vulnerable if they are using NPN instead of ALPN - but NPN is not
widely used. It also requires an application configuration or programming error.
Finally, this issue would not typically be under attacker control making active
exploitation unlikely.
The FIPS modules in 3.3, 3.2, 3.1 and 3.0 are not affected by this issue.
Due to the low severity of this issue we are not issuing new releases of
OpenSSL at this time. The fix will be included in the next releases when they
become available. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: Fix memcpy() field-spanning write warning in mwifiex_cmd_802_11_scan_ext()
Replace one-element array with a flexible-array member in
`struct host_cmd_ds_802_11_scan_ext`.
With this, fix the following warning:
elo 16 17:51:58 surfacebook kernel: ------------[ cut here ]------------
elo 16 17:51:58 surfacebook kernel: memcpy: detected field-spanning write (size 243) of single field "ext_scan->tlv_buffer" at drivers/net/wireless/marvell/mwifiex/scan.c:2239 (size 1)
elo 16 17:51:58 surfacebook kernel: WARNING: CPU: 0 PID: 498 at drivers/net/wireless/marvell/mwifiex/scan.c:2239 mwifiex_cmd_802_11_scan_ext+0x83/0x90 [mwifiex] |
| In the Linux kernel, the following vulnerability has been resolved:
tcp_bpf: fix return value of tcp_bpf_sendmsg()
When we cork messages in psock->cork, the last message triggers the
flushing will result in sending a sk_msg larger than the current
message size. In this case, in tcp_bpf_send_verdict(), 'copied' becomes
negative at least in the following case:
468 case __SK_DROP:
469 default:
470 sk_msg_free_partial(sk, msg, tosend);
471 sk_msg_apply_bytes(psock, tosend);
472 *copied -= (tosend + delta); // <==== HERE
473 return -EACCES;
Therefore, it could lead to the following BUG with a proper value of
'copied' (thanks to syzbot). We should not use negative 'copied' as a
return value here.
------------[ cut here ]------------
kernel BUG at net/socket.c:733!
Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 UID: 0 PID: 3265 Comm: syz-executor510 Not tainted 6.11.0-rc3-syzkaller-00060-gd07b43284ab3 #0
Hardware name: linux,dummy-virt (DT)
pstate: 61400009 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
pc : sock_sendmsg_nosec net/socket.c:733 [inline]
pc : sock_sendmsg_nosec net/socket.c:728 [inline]
pc : __sock_sendmsg+0x5c/0x60 net/socket.c:745
lr : sock_sendmsg_nosec net/socket.c:730 [inline]
lr : __sock_sendmsg+0x54/0x60 net/socket.c:745
sp : ffff800088ea3b30
x29: ffff800088ea3b30 x28: fbf00000062bc900 x27: 0000000000000000
x26: ffff800088ea3bc0 x25: ffff800088ea3bc0 x24: 0000000000000000
x23: f9f00000048dc000 x22: 0000000000000000 x21: ffff800088ea3d90
x20: f9f00000048dc000 x19: ffff800088ea3d90 x18: 0000000000000001
x17: 0000000000000000 x16: 0000000000000000 x15: 000000002002ffaf
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: ffff8000815849c0 x9 : ffff8000815b49c0
x8 : 0000000000000000 x7 : 000000000000003f x6 : 0000000000000000
x5 : 00000000000007e0 x4 : fff07ffffd239000 x3 : fbf00000062bc900
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 00000000fffffdef
Call trace:
sock_sendmsg_nosec net/socket.c:733 [inline]
__sock_sendmsg+0x5c/0x60 net/socket.c:745
____sys_sendmsg+0x274/0x2ac net/socket.c:2597
___sys_sendmsg+0xac/0x100 net/socket.c:2651
__sys_sendmsg+0x84/0xe0 net/socket.c:2680
__do_sys_sendmsg net/socket.c:2689 [inline]
__se_sys_sendmsg net/socket.c:2687 [inline]
__arm64_sys_sendmsg+0x24/0x30 net/socket.c:2687
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x48/0x110 arch/arm64/kernel/syscall.c:49
el0_svc_common.constprop.0+0x40/0xe0 arch/arm64/kernel/syscall.c:132
do_el0_svc+0x1c/0x28 arch/arm64/kernel/syscall.c:151
el0_svc+0x34/0xec arch/arm64/kernel/entry-common.c:712
el0t_64_sync_handler+0x100/0x12c arch/arm64/kernel/entry-common.c:730
el0t_64_sync+0x19c/0x1a0 arch/arm64/kernel/entry.S:598
Code: f9404463 d63f0060 3108441f 54fffe81 (d4210000)
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
DIV_ROUND_CLOSEST() after kstrtol() results in an underflow if a large
negative number such as -9223372036854775808 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations. |
| An issue was discovered in libexpat before 2.6.3. nextScaffoldPart in xmlparse.c can have an integer overflow for m_groupSize on 32-bit platforms (where UINT_MAX equals SIZE_MAX). |
| An issue was discovered in libexpat before 2.6.3. dtdCopy in xmlparse.c can have an integer overflow for nDefaultAtts on 32-bit platforms (where UINT_MAX equals SIZE_MAX). |
| An issue was discovered in libexpat before 2.6.3. xmlparse.c does not reject a negative length for XML_ParseBuffer. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix overflow in get_free_elt()
"tracing_map->next_elt" in get_free_elt() is at risk of overflowing.
Once it overflows, new elements can still be inserted into the tracing_map
even though the maximum number of elements (`max_elts`) has been reached.
Continuing to insert elements after the overflow could result in the
tracing_map containing "tracing_map->max_size" elements, leaving no empty
entries.
If any attempt is made to insert an element into a full tracing_map using
`__tracing_map_insert()`, it will cause an infinite loop with preemption
disabled, leading to a CPU hang problem.
Fix this by preventing any further increments to "tracing_map->next_elt"
once it reaches "tracing_map->max_elt". |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: Fix array-index-out-of-bounds in diFree |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix infinite loop when replaying fast_commit
When doing fast_commit replay an infinite loop may occur due to an
uninitialized extent_status struct. ext4_ext_determine_insert_hole() does
not detect the replay and calls ext4_es_find_extent_range(), which will
return immediately without initializing the 'es' variable.
Because 'es' contains garbage, an integer overflow may happen causing an
infinite loop in this function, easily reproducible using fstest generic/039.
This commit fixes this issue by unconditionally initializing the structure
in function ext4_es_find_extent_range().
Thanks to Zhang Yi, for figuring out the real problem! |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: check dot and dotdot of dx_root before making dir indexed
Syzbot reports a issue as follows:
============================================
BUG: unable to handle page fault for address: ffffed11022e24fe
PGD 23ffee067 P4D 23ffee067 PUD 0
Oops: Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 PID: 5079 Comm: syz-executor306 Not tainted 6.10.0-rc5-g55027e689933 #0
Call Trace:
<TASK>
make_indexed_dir+0xdaf/0x13c0 fs/ext4/namei.c:2341
ext4_add_entry+0x222a/0x25d0 fs/ext4/namei.c:2451
ext4_rename fs/ext4/namei.c:3936 [inline]
ext4_rename2+0x26e5/0x4370 fs/ext4/namei.c:4214
[...]
============================================
The immediate cause of this problem is that there is only one valid dentry
for the block to be split during do_split, so split==0 results in out of
bounds accesses to the map triggering the issue.
do_split
unsigned split
dx_make_map
count = 1
split = count/2 = 0;
continued = hash2 == map[split - 1].hash;
---> map[4294967295]
The maximum length of a filename is 255 and the minimum block size is 1024,
so it is always guaranteed that the number of entries is greater than or
equal to 2 when do_split() is called.
But syzbot's crafted image has no dot and dotdot in dir, and the dentry
distribution in dirblock is as follows:
bus dentry1 hole dentry2 free
|xx--|xx-------------|...............|xx-------------|...............|
0 12 (8+248)=256 268 256 524 (8+256)=264 788 236 1024
So when renaming dentry1 increases its name_len length by 1, neither hole
nor free is sufficient to hold the new dentry, and make_indexed_dir() is
called.
In make_indexed_dir() it is assumed that the first two entries of the
dirblock must be dot and dotdot, so bus and dentry1 are left in dx_root
because they are treated as dot and dotdot, and only dentry2 is moved
to the new leaf block. That's why count is equal to 1.
Therefore add the ext4_check_dx_root() helper function to add more sanity
checks to dot and dotdot before starting the conversion to avoid the above
issue. |
| In the Linux kernel, the following vulnerability has been resolved:
kobject_uevent: Fix OOB access within zap_modalias_env()
zap_modalias_env() wrongly calculates size of memory block to move, so
will cause OOB memory access issue if variable MODALIAS is not the last
one within its @env parameter, fixed by correcting size to memmove. |
| In the Linux kernel, the following vulnerability has been resolved:
x86: stop playing stack games in profile_pc()
The 'profile_pc()' function is used for timer-based profiling, which
isn't really all that relevant any more to begin with, but it also ends
up making assumptions based on the stack layout that aren't necessarily
valid.
Basically, the code tries to account the time spent in spinlocks to the
caller rather than the spinlock, and while I support that as a concept,
it's not worth the code complexity or the KASAN warnings when no serious
profiling is done using timers anyway these days.
And the code really does depend on stack layout that is only true in the
simplest of cases. We've lost the comment at some point (I think when
the 32-bit and 64-bit code was unified), but it used to say:
Assume the lock function has either no stack frame or a copy
of eflags from PUSHF.
which explains why it just blindly loads a word or two straight off the
stack pointer and then takes a minimal look at the values to just check
if they might be eflags or the return pc:
Eflags always has bits 22 and up cleared unlike kernel addresses
but that basic stack layout assumption assumes that there isn't any lock
debugging etc going on that would complicate the code and cause a stack
frame.
It causes KASAN unhappiness reported for years by syzkaller [1] and
others [2].
With no real practical reason for this any more, just remove the code.
Just for historical interest, here's some background commits relating to
this code from 2006:
0cb91a229364 ("i386: Account spinlocks to the caller during profiling for !FP kernels")
31679f38d886 ("Simplify profile_pc on x86-64")
and a code unification from 2009:
ef4512882dbe ("x86: time_32/64.c unify profile_pc")
but the basics of this thing actually goes back to before the git tree. |
