| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: master: svc: bound IBI payload to the requested max_payload_len
svc_i3c_master_handle_ibi() reads the IBI payload from the RX FIFO into
the IBI slot. The loop is bounded by the hardware FIFO size
(SVC_I3C_FIFO_SIZE), not by the slot size.
slot->data points into the IBI pool, which i3c_generic_ibi_alloc_pool()
sizes at max_payload_len per slot. svc_i3c_master_request_ibi() only
rejects a max_payload_len larger than SVC_I3C_FIFO_SIZE, so a driver can
request a smaller one. mctp-i3c requests 1. Each readsb() then copies the
controller RXCOUNT bytes (up to 31) with no check against the slot size.
A device that sends more bytes than the slot holds writes past
slot->data, an out-of-bounds write into the IBI pool.
Bound the loop by dev->ibi->max_payload_len and clamp each read to the
space left in the slot, the same way dw-i3c does. A device can still send
more than the requested payload. Flush the leftover bytes from the RX FIFO
so they do not leak into the next transfer. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: Fix memory leak in brcmf_sdio_read_control()
The memory allocated for buf is not freed in some of the error paths in
brcmf_sdio_read_control(). Fix that by adding vfree() calls.
[arend: rework as suggested by Johannes] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: dvm: fix memory leak in iwl_op_mode_dvm_start()
In iwl_op_mode_dvm_start(), jumping to out_free_eeprom currently bypasses
the out_free_eeprom_blob label. Consequently, error paths triggered after
successfully parsing the EEPROM free priv->nvm_data but leak
priv->eeprom_blob.
Fix this memory leak by reordering the error handling labels so
that out_free_eeprom falls through to out_free_eeprom_blob.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc6.
An x86_64 allyesconfig build showed no new warnings. As we do not have
supported Intel DVM wireless hardware and firmware to test with, no
runtime testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: copy request headers via a stack buffer for io-uring
The fuse-io-uring transport copies req->in.h out to the ring in
fuse_uring_copy_to_ring() and req->out.h back in fuse_uring_commit().
Both headers live inside the fuse_request slab object, whose cache
(fuse_req_cachep) is created without a usercopy whitelist, so copying
them directly to/from userspace trips CONFIG_HARDENED_USERCOPY and
panics:
usercopy: Kernel memory exposure attempt detected from SLUB object
'fuse_request' (offset 56, size 40)!
kernel BUG at mm/usercopy.c:102!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:usercopy_abort (mm/usercopy.c:90)
Call Trace:
__check_heap_object (mm/slub.c:8268)
__check_object_size (mm/usercopy.c:197 mm/usercopy.c:258 mm/usercopy.c:223)
copy_header_to_ring (fs/fuse/dev_uring.c:618)
fuse_uring_prepare_send (fs/fuse/dev_uring.c:776 fs/fuse/dev_uring.c:785)
fuse_uring_send_in_task (fs/fuse/dev_uring.c:1306)
tctx_task_work_run (io_uring/tw.c:96)
task_work_run (kernel/task_work.c:233)
io_run_task_work (io_uring/tw.h:84)
io_cqring_wait (io_uring/wait.c:278)
__do_sys_io_uring_enter (io_uring/io_uring.c:2685)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
Bounce both headers through an on-stack copy so the usercopy touches
stack memory, not the slab object. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: rtl8192du: Fix possible memory leak in rtl92du_init_sw_vars()
The memory allocated inside rtl92du_init_shared_data() is not freed in
any of the subsequent error paths in rtl92du_init_sw_vars().
Fix that by adding a call to rtl92du_deinit_shared_data() in the error
path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: Fix potential memory leak in rtw_txq_push_skb()
The skb passed to the rtw_hci_tx_write() is expected to be freed when
the function fails, but the error path in rtw_txq_push_skb() does not
free the skb before returning. This can lead to a memory leak in
rtw_txq_push() where a dequeued skb is passed to rtw_txq_push_skb(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: pci: fix resource leak on failed NAPI setup
rtw_pci_probe() allocates PCI resources through
rtw_pci_setup_resource() before it sets up NAPI. If
rtw_pci_napi_init() fails, the error path jumps straight to
err_pci_declaim and skips rtw_pci_destroy(), leaving the PCI
resources allocated by rtw_pci_setup_resource() behind.
Add a dedicated cleanup label for the NAPI setup failure path so probe
destroys the PCI resources.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing current
mainline kernels. The tool is still under development and is not yet
publicly available. Manual inspection confirms that the bug is still
present in v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
suitable rtw88 PCI board to test with, no runtime testing was able to be
performed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: pci: add .shutdown callback to stop rfkill polling on reboot
Since the hardware rfkill polling was introduced, arm64 platforms can
panic with an asynchronous SError during warm reboot:
SError Interrupt on CPU8, code 0x00000000be000011 -- SError
Workqueue: events_power_efficient rfkill_poll [rfkill]
rtw89_pci_ops_read8+0x94/0x160 [rtw89_pci]
rtw89_core_rfkill_poll+0x50/0x1e0 [rtw89_core]
rtw89_ops_rfkill_poll+0x40/0x68 [rtw89_core]
ieee80211_rfkill_poll+0x3c/0x70 [mac80211]
cfg80211_rfkill_poll+0x40/0x2a0 [cfg80211]
rfkill_poll+0x30/0x88 [rfkill]
Kernel panic - not syncing: Asynchronous SError Interrupt
On the reboot path the kernel only runs device_shutdown(), which calls
each driver's .shutdown callback; .remove is not invoked. The rtw89 PCI
driver had no .shutdown callback, so nothing stopped the rfkill polling
work while the platform was tearing the PCIe link down. Once the link
is gone, the next MMIO read from the poll handler targets a
non-responding device and is reported as a fatal asynchronous SError on
arm64.
Add rtw89_pci_shutdown(), wired to all rtw89 PCI device drivers, which
sets a new RTW89_FLAG_SHUTDOWN flag (mirroring the USB
RTW89_FLAG_UNPLUGGED pattern). When the flag is set,
rtw89_ops_rfkill_poll() returns early, so no MMIO read is issued to the
chip after shutdown begins and the SError no longer occurs.
This does not call the full .remove path from .shutdown, to keep the
shutdown handler minimal and avoid running the non-idempotent teardown
twice. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7615: avoid waiting for mac work under the mt76 mutex
mt7615_suspend() acquired the mt76 mutex and then called
cancel_delayed_work_sync() on mac_work. mt7615_mac_work() acquires the
same mutex via mt7615_mutex_acquire() at the top of the worker, so if
mac_work is already running and blocked on the mutex, the suspend path
deadlocks waiting for the work it holds the mutex against.
Flush scan_work and mac_work before taking the mutex, matching the
suspend paths in mt7921 and mt7925. scan_work only takes the mt76
spinlock, but moving it keeps the sequence consistent. This also keeps
mac_work from running over an already suspended HIF, which the previous
split (async cancel under the lock, sync cancel after release) would
have allowed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix TX DMA mapping leak for AddBA req frames
mt7996/mt7992 hand the firmware a HW MAC-TXP for AddBA req action frames
(MT_TXD7_MAC_TXD, set in mt7996_mac_write_txwi_80211()), but are otherwise
FW-TXP devices. On tx free mt76_connac_txp_skb_unmap() therefore decodes
the per-frame txp as a struct mt76_connac_fw_txp. For a MAC-TXP the
fw_txp.nbuf byte aliases the AddBA TID word (MT_TXP1_TID_ADDBA), which is
always zero, so the unmap loop runs zero times and the skb DMA mapping in
buf[1] is never unmapped. buf[1].skip_unmap is set unconditionally, so the
generic DMA-ring cleanup skips it as well.
Each AddBA req therefore leaks one TX DMA mapping, roughly one per
(re)association. With WED enabled these mappings are bounced through the
WED swiotlb pool, so under continuous client reconnect churn the pool is
exhausted after ~1-2 days, after which DMA mapping fails for WED, the WiFi
MCU and other on-SoC consumers.
Keep the deferred (token release) unmap that the design relies on, and add
an mt7996-specific txp unmap that inspects MT_TXD7_MAC_TXD and unmaps
buf[1] from the MAC-TXP layout for those frames, delegating to
mt76_connac_txp_skb_unmap() otherwise. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_i2c_nuvoton: disable IRQ on wait timeout
i2c_nuvoton_wait_for_stat() enables the IRQ before waiting for the
interrupt handler to report a status change. If the wait times out, or is
interrupted before the handler runs, the function returns without
balancing the enable_irq() call.
Disable the IRQ before leaving the failed wait path. Also preserve an
interrupted wait's original error code instead of converting it to
-ETIMEDOUT inside the helper. |
| In the Linux kernel, the following vulnerability has been resolved:
timekeeping: Check the return value of tk_get_aux_ts64 in __do_adjtimex()
If the auxiliary clock is disabled during tk_get_aux_ts64() but is enabled
before tks->clock_valid is checked, then uninitialized stackdata will be
used in the calculations and indirectly leaked to userspace.
The same race window also exists after this change and also for the core
timekeeper. But in these cases the only effect would be incorrect
adjustments and this is userspace's responsibility to avoid this. |
| A flaw was found in the Linux kernel. This flaw allows an attacker to crash the Linux kernel by simulating amateur radio from the user space, resulting in a null-ptr-deref vulnerability and a use-after-free vulnerability. |
| In the Linux kernel, the following vulnerability has been resolved:
vlan: fix skb_under_panic and races when toggling HW VLAN offload
Toggling hardware VLAN TX offload (NETIF_F_HW_VLAN_CTAG_TX or
NETIF_F_HW_VLAN_STAG_TX) on a lower device invokes vlan_transfer_features(),
which dynamically changed vlandev->hard_header_len.
This causes two issues:
1. Lockless TX paths (e.g. packet_snd in af_packet.c, ip6_finish_output2)
read dev->hard_header_len without holding RTNL lock. Mutating
hard_header_len dynamically under RTNL creates a data race where upper
layers reserve insufficient headroom based on a stale hard_header_len,
resulting in skb_under_panic when vlan_dev_hard_header() is called.
2. In addition, vlan_transfer_features() updated hard_header_len without
updating header_ops, causing a mismatch between allocated headroom
and header creation.
Always setting dev->hard_header_len = real_dev->hard_header_len and
dev->needed_headroom = real_dev->needed_headroom + VLAN_HLEN unconditionally
ensures:
- dev->hard_header_len remains 100% static and immutable at real_dev->hard_header_len,
eliminating all dynamic runtime updates and data races on hard_header_len.
- Upper layers allocating skbs via LL_RESERVED_SPACE() will always reserve
sufficient headroom for software VLAN tag insertion (real_dev->hard_header_len +
real_dev->needed_headroom + VLAN_HLEN).
- vlandev inherits real_dev->needed_tailroom so underlying trailer/padding/ICV
requirements are honored.
- AF_PACKET SOCK_RAW network header offsets remain correctly aligned at
real_dev->hard_header_len.
- vlan_header_ops is used unconditionally.
Note to stable teams: Make sure to backport these commits:
e16e960d55a4 ("ipvlan: inherit needed_headroom and needed_tailroom from phy_dev")
cef51860becd ("macvlan: inherit needed_headroom and needed_tailroom from lowerdev") |
| In the Linux kernel, the following vulnerability has been resolved:
afs: Fix leak of ungot volume
Fix afs_lookup_volume_rcu() so that it doesn't leak a dying volume if
afs_try_get_volume() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: bail out of setup if the controller is inaccessible
xhci_gen_setup() locates the operational registers using the capability
length read from the very first register:
xhci->op_regs = hcd->regs +
HC_LENGTH(readl(&xhci->cap_regs->hc_capbase));
If the controller is dead or has dropped off the bus, that read returns
~0, HC_LENGTH() truncates it to 0xff, and op_regs ends up 0xff bytes
past the page-aligned MMIO base, i.e. unaligned. The first access
through it, xhci_halt() -> xhci_handshake() reading op_regs->status, is
then an unaligned readl() on device memory. arm64 faults on unaligned
device accesses, so instead of xhci_handshake() catching the all-ones
value and returning -ENODEV, setup oopses:
xhci-pci-renesas 0005:08:00.0: Unable to change power state from D3cold to D0, device inaccessible
xhci-pci-renesas 0005:08:00.0: xHCI Host Controller
xhci-pci-renesas 0005:08:00.0: new USB bus registered, assigned bus number 1
Unable to handle kernel paging request at virtual address ffff80030a770103
ESR = 0x0000000096000021
FSC = 0x21: alignment fault
Internal error: Oops: 0000000096000021 [#1] SMP
pc : xhci_halt [xhci_hcd]
Call trace:
xhci_halt
xhci_gen_setup
xhci_pci_setup
usb_add_hcd
usb_hcd_pci_probe
xhci_pci_common_probe
xhci_pci_renesas_probe
This was hit with a Renesas uPD720201 that failed to power up ("Unable
to change power state from D3cold to D0, device inaccessible") yet still
reached the HCD probe path.
Read the capability register once, and if it reads back the all-ones
value (as xhci_handshake() and xhci_reset() already test for), abort
setup with -ENODEV before op_regs is derived from it. Reading it once
also avoids re-reading a register that may change under a concurrent
hot-removal. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix race between interrupt and resend
After commit f8fce75fedf7 ("fuse: clear intr_entry in fuse_resend and
fuse_remove_pending_req") the WARN_ON(!list_empty(&req->intr_entry)) in
fuse_request_free() still triggers due to the following race:
In request_wait_answer()
if (test_bit(FR_SENT, &req->flags)) -> returns true
In fuse_chan_resend()
clear_bit(FR_SENT, &req->flags)
In request_wait_answer()
queue_interrupt(req)
Fix by:
- move clearing FR_SENT inside fpq->lock
- move setting FR_PENDING inside fiq->lock
- recheck FR_SENT after acquiring fiq->lock in fuse_dev_queue_interrupt() |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix missing barrier when checking io-uring readiness
fuse_block_alloc() reads fch->initialized and then fch->io_uring.
fch->io_uring is set before fch->initialized, ordered by the smp_wmb()
in fuse_chan_set_intialized(), but fuse_block_alloc() has no matching
read barrier between the two loads.
This may lead a CPU to observe fch->initialized=1 but fch->io_uring=0,
and skip the check that blocks request allocation until the io-uring
queues are ready. This can reintroduce the lock-order inversion deadlock
that commit 3393ff964e0f prevents.
Add an smp_rmb() barrier to pair with the smp_wmb() in
fuse_chan_set_initialized() to prevent this. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: publish io-uring queues with release semantics
fuse_uring_create_queue() initializes a fuse_ring_queue and then
publishes the pointer into ring->queues[qid] with WRITE_ONCE() under the
fch->lock. There are several readers that may concurrently be fetching
that pointer locklessly and then deferencing it.
WRITE_ONCE() doesn't ensure ordering of the queue's field
initialization before the ring->queues[qid] pointer assignment. The
queue must be published with smp_store_release() so the field
initialization is guaranteed to happen before.
Readers in paths where the read may happen concurrently with the store
need to use READ_ONCE() because any race involving a plain access is
undefined. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: clamp route advmss to TCP_MIN_MSS
tcp_select_initial_window() assumes that callers never pass an MSS
smaller than 1, but route-derived advmss values can violate that
assumption.
A too-small explicit RTAX_ADVMSS is one way to get there, but it is not
the only one. The same divide-by-zero can also be reached through the
"default advmss" path when RTAX_ADVMSS is left at 0 and the effective
advmss is later driven down by route MTU and min_adv_mss.
Introduce a tcp_dst_advmss() helper that clamps route advmss to
TCP_MIN_MSS before TCP consumes it, and use it in the TCP paths that
derive advmss from dst metrics. This keeps the effective MSS from
dropping to zero before tcp_select_initial_window() rounds the receive
window. |
