| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
media: atomisp: gc2235: fix UAF and memory leak
gc2235_probe() handles its error paths incorrectly.
If media_entity_pads_init() fails, gc2235_remove() is called, which
tears down the subdev and frees dev, but then still falls through to
atomisp_register_i2c_module(). This results in use-after-free.
If atomisp_register_i2c_module() fails, the media entity and control
handler are left initialized and dev is leaked.
gc2235_remove() unconditionally calls media_entity_cleanup() and
v4l2_ctrl_handler_free(), but these are not initialized at every
error path in gc2235_probe().
Replace gc2235_remove() calls in the probe error paths with explicit
unwind labels that free only the resources initialized at each point
of failure, in reverse order of initialization. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp/sev-dev-tsm - bail out early when pdev->bus is NULL
dsm_create() initially checks pdev->bus when computing segment_id:
u8 segment_id = pdev->bus ? pci_domain_nr(pdev->bus) : 0;
But the next two lines unconditionally dereference pdev->bus via
pcie_find_root_port() and especially pci_dev_id(pdev), which expands
to PCI_DEVID(dev->bus->number, dev->devfn). If pdev->bus is in fact
NULL, segment_id is initialised to 0 but the very next statement
crashes the kernel.
smatch flags this:
drivers/crypto/ccp/sev-dev-tsm.c:253 dsm_create() error: we
previously assumed 'pdev->bus' could be null (see line 251)
Make the NULL handling consistent: if pdev->bus is NULL the device
has no PCI context to work with and SEV TIO setup cannot proceed,
so return -ENODEV before any of the bus-dependent lookups. The
remaining initialisation now runs only on the path where pdev->bus
is known to be valid.
No change for callers where pdev->bus is non-NULL, which is the
only case where dsm_create() did meaningful work before this change. |
| In the Linux kernel, the following vulnerability has been resolved:
soc: xilinx: Fix race condition in event registration
The zynqmp_power driver registers handlers for suspend and subsystem
restart events using register_event(). However, the work structures
(zynqmp_pm_init_suspend_work and zynqmp_pm_init_restart_work) used by
these handlers were allocated and initialized after the registration
call.
This created a race window where, if the firmware triggered an event
immediately after registration but before allocation, the callback
(suspend_event_callback or subsystem_restart_event_callback) would
dereference a NULL pointer in work_pending(), leading to a crash.
Fix this by allocating and initializing the work structures before
registering the events. |
| In the Linux kernel, the following vulnerability has been resolved:
hfsplus: Add a sanity check for btree node size
Syzbot reported an uninit-value bug in [1] with a corrupted HFS+ image,
during the file system mounting process, specifically while loading the
catalog, a corrupted node_size value of 1 caused the rec_off argument
passed to hfs_bnode_read_u16() (within hfs_bnode_find()) to be excessively
large. Consequently, the function failed to return a valid value to
initialize the off variable, triggering the bug [1].
Every node starts from BTree node descriptor: struct hfs_bnode_desc.
So, the size of node cannot be lesser than that. However, technical
specification declares that: "The node size (which is expressed in bytes)
must be power of two, from 512 through 32,768, inclusive." Add a check
for btree node size base on technical specification.
[1]
BUG: KMSAN: uninit-value in hfsplus_bnode_find+0x141c/0x1600 fs/hfsplus/bnode.c:584
hfsplus_bnode_find+0x141c/0x1600 fs/hfsplus/bnode.c:584
hfsplus_btree_open+0x169a/0x1e40 fs/hfsplus/btree.c:382
hfsplus_fill_super+0x111f/0x2770 fs/hfsplus/super.c:553
get_tree_bdev_flags+0x6e6/0x920 fs/super.c:1694
get_tree_bdev+0x38/0x50 fs/super.c:1717
hfsplus_get_tree+0x35/0x40 fs/hfsplus/super.c:709
vfs_get_tree+0xb3/0x5d0 fs/super.c:1754
fc_mount fs/namespace.c:1193 [inline] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/rockchip: dw_dp: Fix null-ptr-deref in dw_dp_remove()
Attempting to access driver data in the platform driver ->remove()
callback may lead to a null pointer dereference since there is no
guaranty that the component ->bind() callback invoking
platform_set_drvdata() was executed.
A common scenario is when Rockchip DRM driver didn't manage to run
component_bind_all() because of an (unrelated) error causing early
return from rockchip_drm_bind().
Drop the unnecessary call to platform_get_drvdata() and, instead,
reference the target device structure via platform_device. |
| A server-ide request forgery (SSRF) vulnerability in webhook in Synology Chat Server before 2.4.5-22148 allows remote authenticated users to obtain non-sensitive information. |
| An improper neutralization of input during web page generation ('Cross-site Scripting') vulnerability in extract domain in Synology Chat Server before 2.4.5-22148 allows remote authenticated users, via a UI interaction, to read or write restricted files and conduct limited denial-of-service attacks in DSM. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (occ) unregister sysfs devices outside occ lock
occ_active(false) and occ_shutdown() unregister sysfs-backed devices while
occ->lock is held. hwmon_device_unregister() and sysfs_remove_group() can
wait for active sysfs callbacks to drain, and those callbacks can enter the
OCC update path and try to take occ->lock again. That gives the unregister
paths the lock ordering occ->lock -> sysfs callback drain, while a callback
has the opposite edge sysfs callback -> occ->lock.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the real unregister and callback carrier:
occ_shutdown()
hwmon_device_unregister()
occ_show_temp_1()
occ_update_response()
Lockdep reported the circular dependency with occ_shutdown() already
holding the OCC mutex and hwmon_device_unregister() waiting on the sysfs
side:
WARNING: possible circular locking dependency detected
... (sysfs_lock) ... at: hwmon_device_unregister+0x12/0x30 [vuln_msv]
... (&test_occ.lock) ... at: occ_shutdown.constprop.0+0xe/0x40 [vuln_msv]
occ_update_response.isra.0+0xb/0x20 [vuln_msv]
occ_show_temp_1.constprop.0.isra.0+0x23/0x40 [vuln_msv]
*** DEADLOCK ***
Serialize hwmon registration and removal with a separate hwmon_lock.
Under that lock, detach occ->hwmon and update occ->active while occ->lock
is held so concurrent OCC state changes still see a stable state, then
drop occ->lock before calling hwmon_device_unregister(). Remove the
driver sysfs group before taking occ->lock in occ_shutdown(), so draining
the driver attributes cannot wait while the OCC mutex is held. Also make
OCC update callbacks return -ENODEV after deactivation, so callbacks that
already passed sysfs active protection do not poll the hardware after
teardown has detached the hwmon device. |
| In the Linux kernel, the following vulnerability has been resolved:
tools/power/x86/intel-speed-select: Harden daemon pidfile open
Avoid symlink-based pidfile clobbering by opening the pidfile with
O_NOFOLLOW and validating it with fstat() before locking/writing.
The daemon currently uses a fixed pidfile path under /tmp. A local
unprivileged user can pre-create a symlink at that path and cause a
root-run daemon instance to write into an attacker-chosen file. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: LAG, MPESW, Fix missing complete() on devcom error
mlx5_mpesw_work() returned without calling complete() when
mlx5_lag_get_devcom_comp() returned NULL. A caller that queued the
work and waited on mpesww->comp would block indefinitely.
Funnel the early-return path through a new "complete" label so the
waiter is always woken. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: validate external BO copy bounds for both stride paths
vmw_external_bo_copy() trusts caller-supplied offsets, strides, and
heights and operates on imported dma-buf vmaps:
- The equal-stride memcpy() bound was clamped after subtracting the
offsets from dst_size and src_size; an offset larger than the BO
size wraps the unsigned subtraction to a huge value and the
resulting memcpy() runs off the end of the vmap. dst_stride *
height is also a u32 multiplication that can overflow.
- The non-equal-stride row-by-row path had no bound at all. The
loop touches bytes through offset + (height - 1) * stride +
width_in_bytes, with only a WARN_ON(dst_stride < width_in_bytes),
and could likewise step past the end of either mapping.
The offsets and strides are derived from STDU/SOU plane state, so a
configured CRTC submitting a crafted atomic commit on an imported
framebuffer can reach this path.
Validate the exact row-copy endpoint against each BO's size up front
using check_mul_overflow() and check_add_overflow(). Use the bulk
memcpy() path only when width_in_bytes covers the whole stride;
otherwise copy one row at a time so partial-row updates near the bottom
of a framebuffer remain valid. Also reject zero strides and stride <
width_in_bytes, both of which the row-by-row path cannot represent
safely. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: fix guest_memory_dirty bitfield clobbered as size
Two sites in vmwgfx_resource.c assign boolean literals to
res->guest_memory_size, which is an unsigned long allocation-size
field; the intended target is the adjacent res->guest_memory_dirty
bitfield. After the assignments the field holds 0 or 1 instead of
the resource's MOB allocation size:
- vmw_resource_release() writes 0 (false), and
- vmw_resource_unbind_list() writes 1 (true).
Subsequent revalidation paths read guest_memory_size when computing
the dirty page range (vmw_bo_dirty_transfer_to_res()) and the buffer
allocation size (vmw_resource_buf_alloc()), producing zero-length
walks or wrap-around ranges that read or write past the MOB bitmap.
The dirty-tracking intent of the original code (mark the resource as
dirtied since the last sync) is also lost, since guest_memory_dirty
is never updated.
Rename both assignments to guest_memory_dirty. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: use proper context for logging
The same as the rest of the code, get_ss_info_from_atombios() uses
calc_pll_cs->ctx->logger for logging. But calc_pll_cs->ctx is
initialized only later in calc_pll_max_vco_construct(). Therefore, any
output using DC_LOG_SYNC() leads to a NULL pointer deference in
get_ss_info_from_atombios().
According to Sashiko, the very same problem exists in
dce112_get_pix_clk_dividers() and dcn3_get_pix_clk_dividers() too.
To avoid accessing the NULL context, use clk_src->base.ctx->logger
everywhere. That context in base is initialized earlier in
dce110_clk_src_construct() and dce112_clk_src_construct(). Before
get_ss_info_from_atombios() or Sashiko's get_pix_clk_dividers functions
above are actually called. This is done by redefining DC_LOGGER to
CTX->logger.
Before:
dce110_clk_src_construct() did:
-> sets clk_src->base.ctx = ctx;
-> ss_info_from_atombios_create()
-> get_ss_info_from_atombios() <- uses calc_pll_cs->ctx # BOOM
-> calc_pll_max_vco_construct() <- sets calc_pll_cs->ctx
After:
dce110_clk_src_construct() does:
-> sets clk_src->base.ctx = ctx;
-> ss_info_from_atombios_create()
-> get_ss_info_from_atombios() <- uses clk_src->base.ctx
(cherry picked from commit 6f16fcbb0c46a87e3d9685407e906573d60104b0) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: check if dml21_add_phantom_plane() is successful
Verify that the phantom plane was allocated to avoid a later
segfault.
(cherry picked from commit 5adb54abe5a8e82cbff7f8806db30a5f4924329f) |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: wake linked drain waiters on unlink
snd_pcm_drain() on a linked stream parks an on-stack wait entry on the
drained peer's runtime->sleep, and after schedule_timeout() removes it
only if that peer is still found in the caller's group. If group
membership changes during the wait and the sleep ends by signal or
timeout (so autoremove_wake_function() does not run), finish_wait() is
skipped and snd_pcm_drain() returns with the entry still queued on that
stream's sleep list; a later wake_up() then walks a freed stack frame.
This is reachable by unlinking either the drained or the draining stream.
Unlike the close path (snd_pcm_drop() -> snd_pcm_post_stop()),
snd_pcm_unlink() never wakes the sleep queues. Wake every group member
under the group lock before the membership change, so a linked drainer is
released and drops its entry while the streams are still grouped.
The window was opened when snd_pcm_link_rwsem stopped being held across
the wait and the removal became conditional on group membership (see
Fixes). The later switch to finish_wait() kept that conditional removal,
so the signal/timeout case remained. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate Adaptation Indication parameter length
The Adaptation Layer Indication parameter contains a fixed 32-bit
Adaptation Code Point after its parameter header. However,
sctp_verify_param() accepts a header-only parameter because the generic
parameter walker only requires the header to be present.
sctp_process_param() then reads adaptation_ind beyond the declared
parameter. When the malformed parameter is last in an INIT, the read
starts at the receive skb tail, and the value is copied into the state
cookie returned in the INIT ACK. This may disclose four receive-buffer
tail bytes.
Require the declared parameter length to match the fixed structure size
and abort the association through the existing invalid parameter length
path otherwise. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/percpu-km: fix bitmap overflow and accounting in pcpu_create_chunk()
In pcpu_create_chunk(), nr_pages is the total contiguous backing
allocation, i.e., nr_units * pcpu_unit_pages, but pcpu_chunk_populated()
uses it to set chunk->populated, whose size is pcpu_unit_pages, bitmap.
Since bit N in chunk->populated means page offset N inside every unit is
backed. When nr_units > 1, the function writes beyond chunk->populated.
Fix it by using chunk->nr_pages.
It also fixes the global pcpu_nr_empty_pop_pages accounting, since
pcpu_balance_free() only iterates up to chunk->nr_pages.
Commit a63d4ac4ab609 ("percpu: make percpu-km set chunk->populated bitmap
properly") introduced the bitmap overflow issue. Later, commit
b539b87fed37f ("percpu: implmeent pcpu_nr_empty_pop_pages and
chunk->nr_populated") added pcpu_nr_empty_pop_pages and caused the
accounting issue. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: mglru: fix stale batch updates after memcg reparenting
The mglru page table walker batches per-generation size deltas in
walk->nr_pages while walking page tables without holding the lruvec lock.
The reset_batch_size() later folds those deltas into walk->lruvec under
the lruvec lock.
The page table walker can run concurrently with the memcg reparenting path
as follows:
CPU0 CPU1
==== ====
walk_mm
--> walk_page_range
--> update_batch_size
--> walk->nr_pages += delta
mem_cgroup_css_offline
--> memcg_reparent_objcgs
--> lock lruvec
lru_gen_reparent_memcg
--> reparent child folios to parent
unlock lruvec
lock lruvec
reset_batch_size
--> child lrugen->nr_pages += delta
This will trigger the following warning in lru_gen_exit_memcg():
VM_WARN_ON_ONCE(memchr_inv(lruvec->lrugen.nr_pages, 0,
sizeof(lruvec->lrugen.nr_pages)));
And the user-visible impact of underestimated nr_pages in MGLRU was
premature OOMs because MGLRU does not try to reclaim memory when nr_pages
reaches zero, but there are still more pages.
To fix it, make reset_batch_size() check CSS_DYING under RCU before
flushing the pending batch. A non-dying memcg keeps the original lruvec
stable against RCU-delayed offlining; a dying memcg redirects the deltas
to the first non-dying ancestor. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate individual TWT params before driver setup
ieee80211_process_rx_twt_action() only partially validates a received
S1G TWT setup frame before queueing it.
An individual agreement can therefore reach ieee80211_s1g_rx_twt_setup()
with twt->length too short for the full struct ieee80211_twt_params.
The individual path passes twt to drv_add_twt_setup(). Both the tracepoint
and the driver callback consume the complete parameters block, not merely
req_type. Do not pass a short individual agreement to the driver.
Broadcast agreements remain unchanged because they are rejected locally
after accessing only req_type.
[edit commit message to not overclaim lack of validation nor
understate driver impact] |
| A vulnerability was detected in iswalle getnote-mcp up to 1.5.0. The affected element is the function fs.readFileSync of the file src/index.ts of the component upload_image. Performing a manipulation of the argument image_path results in path traversal. The attack can be initiated remotely. The exploit is now public and may be used. Upgrading to version 1.5.1 is sufficient to fix this issue. The patch is named 7f9a215e03575c650d38c8f87fc6d8d363fed80d. Upgrading the affected component is advised. |
