| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix 6 GHz scan construction
If more than 255 colocated APs exist for the set of all
APs found during 2.4/5 GHz scanning, then the 6 GHz scan
construction will loop forever since the loop variable
has type u8, which can never reach the number found when
that's bigger than 255, and is stored in a u32 variable.
Also move it into the loops to have a smaller scope.
Using a u32 there is fine, we limit the number of APs in
the scan list and each has a limit on the number of RNR
entries due to the frame size. With a limit of 1000 scan
results, a frame size upper bound of 4096 (really it's
more like ~2300) and a TBTT entry size of at least 11,
we get an upper bound for the number of ~372k, well in
the bounds of a u32. |
| GNOME libsoup before 3.6.1 has an infinite loop, and memory consumption. during the reading of certain patterns of WebSocket data from clients. |
| In the Linux kernel, the following vulnerability has been resolved:
filemap: Fix bounds checking in filemap_read()
If the caller supplies an iocb->ki_pos value that is close to the
filesystem upper limit, and an iterator with a count that causes us to
overflow that limit, then filemap_read() enters an infinite loop.
This behaviour was discovered when testing xfstests generic/525 with the
"localio" optimisation for loopback NFS mounts. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/sgx: Fix deadlock in SGX NUMA node search
When the current node doesn't have an EPC section configured by firmware
and all other EPC sections are used up, CPU can get stuck inside the
while loop that looks for an available EPC page from remote nodes
indefinitely, leading to a soft lockup. Note how nid_of_current will
never be equal to nid in that while loop because nid_of_current is not
set in sgx_numa_mask.
Also worth mentioning is that it's perfectly fine for the firmware not
to setup an EPC section on a node. While setting up an EPC section on
each node can enhance performance, it is not a requirement for
functionality.
Rework the loop to start and end on *a* node that has SGX memory. This
avoids the deadlock looking for the current SGX-lacking node to show up
in the loop when it never will. |
| In the Linux kernel, the following vulnerability has been resolved:
net, sunrpc: Remap EPERM in case of connection failure in xs_tcp_setup_socket
When using a BPF program on kernel_connect(), the call can return -EPERM. This
causes xs_tcp_setup_socket() to loop forever, filling up the syslog and causing
the kernel to potentially freeze up.
Neil suggested:
This will propagate -EPERM up into other layers which might not be ready
to handle it. It might be safer to map EPERM to an error we would be more
likely to expect from the network system - such as ECONNREFUSED or ENETDOWN.
ECONNREFUSED as error seems reasonable. For programs setting a different error
can be out of reach (see handling in 4fbac77d2d09) in particular on kernels
which do not have f10d05966196 ("bpf: Make BPF_PROG_RUN_ARRAY return -err
instead of allow boolean"), thus given that it is better to simply remap for
consistent behavior. UDP does handle EPERM in xs_udp_send_request(). |
| In the Linux kernel, the following vulnerability has been resolved:
x86/bhi: Avoid warning in #DB handler due to BHI mitigation
When BHI mitigation is enabled, if SYSENTER is invoked with the TF flag set
then entry_SYSENTER_compat() uses CLEAR_BRANCH_HISTORY and calls the
clear_bhb_loop() before the TF flag is cleared. This causes the #DB handler
(exc_debug_kernel()) to issue a warning because single-step is used outside the
entry_SYSENTER_compat() function.
To address this issue, entry_SYSENTER_compat() should use CLEAR_BRANCH_HISTORY
after making sure the TF flag is cleared.
The problem can be reproduced with the following sequence:
$ cat sysenter_step.c
int main()
{ asm("pushf; pop %ax; bts $8,%ax; push %ax; popf; sysenter"); }
$ gcc -o sysenter_step sysenter_step.c
$ ./sysenter_step
Segmentation fault (core dumped)
The program is expected to crash, and the #DB handler will issue a warning.
Kernel log:
WARNING: CPU: 27 PID: 7000 at arch/x86/kernel/traps.c:1009 exc_debug_kernel+0xd2/0x160
...
RIP: 0010:exc_debug_kernel+0xd2/0x160
...
Call Trace:
<#DB>
? show_regs+0x68/0x80
? __warn+0x8c/0x140
? exc_debug_kernel+0xd2/0x160
? report_bug+0x175/0x1a0
? handle_bug+0x44/0x90
? exc_invalid_op+0x1c/0x70
? asm_exc_invalid_op+0x1f/0x30
? exc_debug_kernel+0xd2/0x160
exc_debug+0x43/0x50
asm_exc_debug+0x1e/0x40
RIP: 0010:clear_bhb_loop+0x0/0xb0
...
</#DB>
<TASK>
? entry_SYSENTER_compat_after_hwframe+0x6e/0x8d
</TASK>
[ bp: Massage commit message. ] |
| In the Linux kernel, the following vulnerability has been resolved:
can: mcp251xfd: fix infinite loop when xmit fails
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
[mkl: use more imperative wording in patch description] |
| XRA dissector infinite loop in Wireshark 4.0.0 to 4.0.5 and 3.6.0 to 3.6.13 allows denial of service via packet injection or crafted capture file |
| GDSDB infinite loop in Wireshark 4.0.0 to 4.0.5 and 3.6.0 to 3.6.13 allows denial of service via packet injection or crafted capture file |
| Infinite loops in the BPv6, OpenFlow, and Kafka protocol dissectors in Wireshark 4.0.0 to 4.0.1 and 3.6.0 to 3.6.9 allows denial of service via packet injection or crafted capture file |
| Infinite loop in the F5 Ethernet Trailer protocol dissector in Wireshark 3.6.0 to 3.6.7 and 3.4.0 to 3.4.15 allows denial of service via packet injection or crafted capture file |
| Infinite loop in RTMPT protocol dissector in Wireshark 3.6.0 to 3.6.1 and 3.4.0 to 3.4.11 allows denial of service via packet injection or crafted capture file |
| Large loops in multiple protocol dissectors in Wireshark 3.6.0 to 3.6.1 and 3.4.0 to 3.4.11 allow denial of service via packet injection or crafted capture file |
| Infinite loop in the RTMPT dissector in Wireshark 3.6.0 and 3.4.0 to 3.4.10 allows denial of service via packet injection or crafted capture file |
| Infinite loop in the BitTorrent DHT dissector in Wireshark 3.6.0 and 3.4.0 to 3.4.10 allows denial of service via packet injection or crafted capture file |
| Crash in the RFC 7468 dissector in Wireshark 3.6.0 and 3.4.0 to 3.4.10 allows denial of service via packet injection or crafted capture file |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: fix lockup on tx to unregistering netdev with carrier
Commit in a fixes tag attempted to fix the issue in the following
sequence of calls:
do_output
-> ovs_vport_send
-> dev_queue_xmit
-> __dev_queue_xmit
-> netdev_core_pick_tx
-> skb_tx_hash
When device is unregistering, the 'dev->real_num_tx_queues' goes to
zero and the 'while (unlikely(hash >= qcount))' loop inside the
'skb_tx_hash' becomes infinite, locking up the core forever.
But unfortunately, checking just the carrier status is not enough to
fix the issue, because some devices may still be in unregistering
state while reporting carrier status OK.
One example of such device is a net/dummy. It sets carrier ON
on start, but it doesn't implement .ndo_stop to set the carrier off.
And it makes sense, because dummy doesn't really have a carrier.
Therefore, while this device is unregistering, it's still easy to hit
the infinite loop in the skb_tx_hash() from the OVS datapath. There
might be other drivers that do the same, but dummy by itself is
important for the OVS ecosystem, because it is frequently used as a
packet sink for tcpdump while debugging OVS deployments. And when the
issue is hit, the only way to recover is to reboot.
Fix that by also checking if the device is running. The running
state is handled by the net core during unregistering, so it covers
unregistering case better, and we don't really need to send packets
to devices that are not running anyway.
While only checking the running state might be enough, the carrier
check is preserved. The running and the carrier states seem disjoined
throughout the code and different drivers. And other core functions
like __dev_direct_xmit() check both before attempting to transmit
a packet. So, it seems safer to check both flags in OVS as well. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: imx8mp-blk-ctrl: add missing loop break condition
Currently imx8mp_blk_ctrl_remove() will continue the for loop
until an out-of-bounds exception occurs.
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : dev_pm_domain_detach+0x8/0x48
lr : imx8mp_blk_ctrl_shutdown+0x58/0x90
sp : ffffffc084f8bbf0
x29: ffffffc084f8bbf0 x28: ffffff80daf32ac0 x27: 0000000000000000
x26: ffffffc081658d78 x25: 0000000000000001 x24: ffffffc08201b028
x23: ffffff80d0db9490 x22: ffffffc082340a78 x21: 00000000000005b0
x20: ffffff80d19bc180 x19: 000000000000000a x18: ffffffffffffffff
x17: ffffffc080a39e08 x16: ffffffc080a39c98 x15: 4f435f464f006c72
x14: 0000000000000004 x13: ffffff80d0172110 x12: 0000000000000000
x11: ffffff80d0537740 x10: ffffff80d05376c0 x9 : ffffffc0808ed2d8
x8 : ffffffc084f8bab0 x7 : 0000000000000000 x6 : 0000000000000000
x5 : ffffff80d19b9420 x4 : fffffffe03466e60 x3 : 0000000080800077
x2 : 0000000000000000 x1 : 0000000000000001 x0 : 0000000000000000
Call trace:
dev_pm_domain_detach+0x8/0x48
platform_shutdown+0x2c/0x48
device_shutdown+0x158/0x268
kernel_restart_prepare+0x40/0x58
kernel_kexec+0x58/0xe8
__do_sys_reboot+0x198/0x258
__arm64_sys_reboot+0x2c/0x40
invoke_syscall+0x5c/0x138
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x38/0xc8
el0t_64_sync_handler+0x120/0x130
el0t_64_sync+0x190/0x198
Code: 8128c2d0 ffffffc0 aa1e03e9 d503201f |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: avoid avoid truncating 64-bit offset to 32 bits
on 32-bit kernels, iomap_write_delalloc_scan() was inadvertently using a
32-bit position due to folio_next_index() returning an unsigned long.
This could lead to an infinite loop when writing to an xfs filesystem. |
| In the Linux kernel, the following vulnerability has been resolved:
filemap: avoid truncating 64-bit offset to 32 bits
On 32-bit kernels, folio_seek_hole_data() was inadvertently truncating a
64-bit value to 32 bits, leading to a possible infinite loop when writing
to an xfs filesystem. |
