| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: fix UAF when probe runs concurrent to dyn ID removal
Dynamic IDs are only guaranteed to be valid when usb_dynids_lock is held,
as remove_id_store can free the node. Thus, make a copy in
usb_probe_interface. Clarify the documentation that the id parameter is
only valid during the probe.
USB serial has the same pattern, but it does not need fixing as the IDs
cannot be removed via sysfs. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_fs: Fix fence cleanup in ffs_dmabuf_transfer() error paths
The error paths for endpoint-disabled (ESHUTDOWN) and request-allocation
failure (ENOMEM) in ffs_dmabuf_transfer() jump to err_fence_put which
calls dma_fence_put() on the fence. However, at that point the fence has
only been kmalloc'd — dma_fence_init() has not been called yet, so the
refcount and the fence ops are uninitialized. Calling dma_fence_put() on
such an object leads to undefined behavior.
Use kfree() instead, since the fence is just a plain allocation at this
stage, and rename the label to err_fence_free to reflect the actual
cleanup action. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uac: validate rate list length before storing
UAC1 and UAC2 configfs rate-list attributes parse a comma-separated
list of sampling rates and store each parsed value in fixed-size arrays.
The arrays have UAC_MAX_RATES entries, but the store paths do not check
that the input contains at most that many tokens before writing through
opts->name##s[i++].
Writing more than ten rates therefore writes past the end of the
p_srates[] or c_srates[] array in struct f_uac1_opts or struct
f_uac2_opts.
With CONFIG_UBSAN_BOUNDS enabled, writing an 11-entry rate list to the
UAC1 p_srate attribute reports:
UBSAN: array-index-out-of-bounds
drivers/usb/gadget/function/f_uac1.c:1669:1
index 10 is out of range for type 'int [10]'
__ubsan_handle_out_of_bounds.cold
f_uac1_opts_p_srate_store
configfs_write_iter
vfs_write
ksys_write
do_syscall_64
The same reproducer against the UAC2 p_srate attribute reports:
UBSAN: array-index-out-of-bounds
drivers/usb/gadget/function/f_uac2.c:2087:1
index 10 is out of range for type 'int [10]'
__ubsan_handle_out_of_bounds.cold
f_uac2_opts_p_srate_store
configfs_write_iter
vfs_write
ksys_write
do_syscall_64
Reject additional tokens once UAC_MAX_RATES entries have been parsed.
Also keep the original kstrdup() pointer for kfree(), because strsep()
advances the parsing cursor. Freeing the advanced cursor leaks the
original buffer on successful parses and can free an interior pointer on
some error paths. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: asus-wireless: Fail probe when there is no ACPI match
Every platform driver can be forced to match a device that does not match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device ACPI companion
object need to verify its presence.
asus_wireless_probe() returns success when acpi_match_acpi_device()
finds no match, leaving behind an input device that never reports
anything because the notify handler is not installed. Worse, when the
driver is force-bound to a device without an ACPI companion, probe
still succeeds and stores a NULL companion pointer, which
asus_wireless_remove() later passes to acpi_dev_remove_notify_handler(),
leading to a NULL pointer dereference on unbind.
Return -ENODEV when the device does not match the ID table. This also
covers the missing-companion case, because acpi_match_acpi_device()
rejects a NULL device. Perform the check before allocating any driver
state, instead of after the input device has already been registered. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Drop scalar id on sign-extending narrowing stack fills
When a spilled scalar is filled back with a sign-extending narrowing load
(BPF_MEMSX), check_stack_read_fixed_off() copies the spilled register
including its scalar id, but coerce_reg_to_size_sx() then sign-extends the
filled register's value. If the same slot is also filled with a plain
zero-extending load (BPF_MEM), both destination registers share the id yet
hold different values. A later 'if <zext-reg> == const' then refines the
sign-extended register through sync_linked_regs() to a value it does not
have at runtime (e.g. the verifier believes 0x80000000 while the register
is 0xffffffff80000000), which can be turned into an out-of-bounds access.
Drop the shared scalar id at the sign-extension site in check_mem_access()
when sign extension actually changes the value, mirroring the BPF_MOVSX
handling in check_alu_op() (no_sext = reg_umax < 2^(size*8-1)). |
| In the Linux kernel, the following vulnerability has been resolved:
bus: mhi: ep: Fix device refcount leak in the error path of MHI device creation
mhi_ep_create_device() takes one device reference for the UL channel and
another for the DL channel after allocating the transfer device. These
references are normally released by mhi_ep_destroy_device() before the
device itself is removed.
If dev_set_name() or device_add() fails, the error path currently drops
only one reference. The remaining channel references keep the device
from being released and leave the channels associated with a device that
was never registered.
Route both failures through a common unwind path that drops the DL
channel reference, the UL channel reference, and the initial reference
from device_initialize(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix dangling pointer in plane reset function
amdgpu_dm_plane_drm_plane_reset() frees the old state before allocating
a new one. If kzalloc() fails, the function returns without updating
the state pointer, leaving a dangling pointer to already freed memory.
Fix this by allocating the new state first. On allocation failure, the
old state remains untouched and the function safely returns.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
[adjust for movement around current amd-staging-drm-next] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/pm/powerplay: bounds-check voltage index in Vega10 lookup
vddInd, vddciInd and mvddInd from VBIOS-parsed tables index into vddc,
vddci and vddmem lookup tables without bounds checks across nine sites.
Return -EINVAL when any index is out of range. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/pm/powerplay: bounds-check voltage index in SMU7 lookup
vddInd and vddcInd fields from VBIOS-parsed tables are used to index into
voltage lookup tables without a bounds check. Return -EINVAL when any
index is out of range. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/lima: call drm_mm_init() with a valid allocation range
lima_vm_create() is currently run before va_start and va_end are set up,
meaning they are both 0. lima_vm_create() runs drm_mm_init() with them
as arguments for the allocator, and if DRM_DEBUG_MM is enabled the
DRM_MM_BUG_ON check in drm_mm_init then fires, as seen here on
exynos4412-odroid-u2:
[ 1.736297] ------------[ cut here ]------------
[ 1.740370] kernel BUG at drivers/gpu/drm/drm_mm.c:931!
[ 1.745574] Internal error: Oops - BUG: 0 [#1] SMP ARM
[ 1.750697] Modules linked in:
[ 1.753734] CPU: 0 UID: 0 PID: 41 Comm: kworker/u16:1 Not tainted 7.0.10-postmarketos-exynos4 #11 PREEMPT
[ 1.763372] Hardware name: Samsung Exynos (Flattened Device Tree)
[ 1.769446] Workqueue: events_unbound deferred_probe_work_func
[ 1.775261] PC is at drm_mm_init+0x9c/0xa4
[ 1.779339] LR is at lima_vm_create+0x144/0x17c
[ ... ]
Fix the issue by moving the lima_vm_create() call after va_start and
va_end are set up. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: rt700-sdw: always drain jack work on remove
rt700_sdw_remove() drains jack_detect_work and jack_btn_check_work only
when rt700->hw_init is true. That state bit is cleared by
rt700_update_status() when the SoundWire slave becomes UNATTACHED, but a
jack work item can already have been queued by rt700_interrupt_callback()
or rt700_jack_init() while the device was initialized.
Do not use hw_init as the remove-time guard for draining these work
objects. The delayed works are initialized during rt700_init(), so remove
can cancel them unconditionally and pair the object lifetime with the
codec-private data lifetime instead of a mutable hardware state bit.
This issue was found by our static analysis tool and then confirmed by
manual review of the SoundWire status, interrupt and remove paths. The
remove path should drain work based on whether the work object exists, not
on a runtime hardware state bit that can change after the work was queued.
A QEMU PoC queued jack_detect_work, simulated SDW_SLAVE_UNATTACHED, and
then entered remove. DEBUG_OBJECTS reported an active timer/work object
associated with the rt700 jack work path after remove skipped the cancel.
This is sent as an RFC because the practical trigger depends on SoundWire
core remove ordering after an UNATTACHED status update. If remove cannot
run after hw_init has been cleared while jack work is still pending, this
is a defensive lifecycle cleanup rather than a reachable race on current
systems. |
| In the Linux kernel, the following vulnerability has been resolved:
udf: Mark LVID buffer as uptodate before marking it dirty
When an I/O error occurs while writing the Logical Volume Integrity
Descriptor (LVID) buffer to the block device, the block layer's completion
handler (`end_buffer_write_sync()`) clears the `BH_Uptodate` flag on the
buffer. However, the buffer still contains valid LVID data in memory. If
the filesystem is subsequently remounted read-write or synced,
`udf_open_lvid()` or `udf_sync_fs()` will modify the LVID buffer and call
`mark_buffer_dirty()`. This triggers a spurious
`WARN_ON_ONCE(!buffer_uptodate(bh))` warning in `mark_buffer_dirty()`
because the buffer is not marked uptodate, even though its in-memory
contents are valid and are about to be overwritten.
To prevent this spurious warning, unconditionally set the `BH_Uptodate`
flag before calling `mark_buffer_dirty()` in `udf_open_lvid()` and
`udf_sync_fs()`. This acknowledges that the in-memory buffer is valid and
matches the workaround previously applied to `udf_close_lvid()` in commit
853a0c25baf9 ("udf: Mark LVID buffer as uptodate before marking it dirty").
Extending this workaround ensures consistent behavior across all LVID
updates.
Buffer I/O error on dev loop0, logical block 128, lost sync page write
------------[ cut here ]------------
!buffer_uptodate(bh)
WARNING: fs/buffer.c:1087 at mark_buffer_dirty+0x299/0x410 fs/buffer.c:1087
...
Call Trace:
<TASK>
udf_open_lvid+0x369/0x5b0 fs/udf/super.c:2078
udf_reconfigure+0x336/0x540 fs/udf/super.c:679
reconfigure_super+0x232/0x8f0 fs/super.c:1080
vfs_cmd_reconfigure fs/fsopen.c:268 [inline]
vfs_fsconfig_locked+0x171/0x320 fs/fsopen.c:297
__do_sys_fsconfig fs/fsopen.c:463 [inline]
__se_sys_fsconfig+0x6b9/0x810 fs/fsopen.c:350
do_syscall_64+0x174/0x580 arch/x86/entry/syscall_64.c:94
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
time/namespace: Validate nanosecond field in proc_timens_set_offset()
The function validates tv_sec to be within [-KTIME_SEC_MAX, KTIME_SEC_MAX]
but never validates that tv_nsec is within the valid range of
[0, NSEC_PER_SEC-1] before using it in timespec64_add().
timespec64_add() expects both timespec64 structures to have normalized
values with tv_nsec in the range [0, 999999999]. If off->val.tv_nsec
contains invalid values (negative or >= NSEC_PER_SEC), it could lead to
incorrect calculations or unexpected behavior.
Add validation to ensure tv_nsec is within the valid range before
performing the addition. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/bpf: Replace ly instruction with llgf
cpu_nr is a 32 bit value and BPF_REG_0 is a 64 bit register, when ly loads
the cpu_nr into BPF_REG_0 it does not zero the upper bits, but llgf does. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211_hwsim: avoid NULL skb in stop queue drain
mac80211_hwsim_stop() drops any frames left in data->pending. The loop
currently checks skb_queue_empty() and then dequeues separately.
That split is racy with TX status handling, which can remove a pending
frame under the queue lock. If the last entry is removed after the empty
check, skb_dequeue() returns NULL and the stop path passes that NULL skb
to ieee80211_free_txskb().
Use skb_dequeue() as the loop condition instead. The dequeue result is the
object that stop owns and frees, and a concurrent status completion that
empties the queue simply makes the loop terminate. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup/cpuset: Make nr_deadline_tasks an atomic_t
The nr_deadline_tasks variable in the cpuset structure was introduced by
commit 6c24849f5515 ("sched/cpuset: Keep track of SCHED_DEADLINE task
in cpusets"). It is reported by sashiko [1] that nr_deadline_tasks
can currently be modified by inc_dl_tasks_cs() under rq->lock and
by cpuset_attach() under cpuset_mutex. So if both updates happen
simultaneously, the nr_deadline_tasks variable can be corrupted leading
to incorrect operations down the road.
Fix that by changing its type to atomic_t so that nr_deadline_tasks
are always atomically updated. This fix patch is a low hanging fruit.
It can handle some of the races between a concurrent sched_setscheduler()
and cpuset_can_attach()/cpuset_attach() calls, but not all of them like
the other issue raised by sashiko [2]. This will be handled hopefully
in a future follow up patch.
[1] https://sashiko.dev/#/patchset/20260626181923.133658-1-longman%40redhat.com
[2] https://sashiko.dev/#/patchset/20260630033344.352702-1-longman%40redhat.com |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: core - fix rng list on registration error
hwrng_register(rng) does the following:
1. Checks if rng has name and read methods set
2. Checks if the name already exists
3. Adds rng to global rng_list
4. May try to set rng to current_rng
If step 4 fails, it returns an error. However, it does not remove the
rng from rng_list, causing a dangling reference which can result in
use-after-free if the caller frees rng, since registration failed.
Add a list_del_init() cleanup step. |
| In the Linux kernel, the following vulnerability has been resolved:
uprobes/x86: Move optimized uprobe from nop5 to nop10
Andrii reported an issue with optimized uprobes [1] that can clobber
redzone area with call instruction storing return address on stack
where user code may keep temporary data without adjusting rsp.
Fixing this by moving the optimized uprobes on top of 10-bytes nop
instruction, so we can squeeze another instruction to escape the
redzone area before doing the call, like:
lea -0x80(%rsp), %rsp
call tramp
Note the lea instruction is used to adjust the rsp register without
changing the flags.
We use nop10 and following transformation to optimized instructions
above and back as suggested by Peterz [2].
Optimize path (int3_update_optimize):
1) Initial state after set_swbp() installed the uprobe:
cc 2e 0f 1f 84 00 00 00 00 00
From offset 0 this is INT3 followed by the tail of the original
10-byte NOP.
After a previous unoptimization bytes 5..9 may still contain the
old call instruction, which remains valid for threads already there.
2) Rewrite the LEA tail and call displacement:
cc [8d 64 24 80 e8 d0 d1 d2 d3]
From offset 0 this traps on the uprobe INT3. Bytes 1..9 are not
executable entry points while byte 0 is trapped.
3) Publish the first LEA byte:
[48] 8d 64 24 80 e8 d0 d1 d2 d3
From offset 0 this is:
lea -0x80(%rsp), %rsp
call <uprobe-trampoline>
Unoptimize path (int3_update_unoptimize):
1) Initial optimized state:
48 8d 64 24 80 e8 d0 d1 d2 d3
Same as 3) above.
2) Trap new entries before restoring the NOP bytes:
[cc] 8d 64 24 80 e8 d0 d1 d2 d3
From offset 0 this traps. A thread that had already executed the
LEA can still reach the intact CALL at offset 5.
3) Restore bytes 1..4 of the original NOP while keeping byte 0 trapped
and byte 5 as CALL.
cc [2e 0f 1f 84] e8 d0 d1 d2 d3
From offset 0 this still traps. Offset 5 is still the CALL for any
thread that was already past the first LEA byte.
4) Publish the first byte of the original NOP:
[66] 2e 0f 1f 84 e8 d0 d1 d2 d3
From offset 0 this is the restored 10-byte NOP; the CALL opcode and
displacement are now only NOP operands. Offset 5 still decodes as
CALL for a thread that was already there.
Tthere is only a single target uprobe-trampoline for the given nop10
instruction address, so the CALL instruction will not be changed across
unoptimization/optimization cycles.
Therefore, any task that is preempted at the CALL instruction is guaranteed
to observe that CALL and not anything else.
Note as explained in [2] we need to use following nop10:
PF1 PF2 ESC NOPL MOD SIB DISP32
NOP10: 0x66, 0x2e, 0x0f, 0x1f, 0x84, 0x00, 0x00, 0x00, 0x00, 0x00 -- cs nopw 0x00000000(%rax,%rax,1)
which means we need to allow 0x2e prefix which maps to INAT_PFX_CS
attribute in is_prefix_bad function.
Also changing the uprobe syscall error when called out of uprobe
trampoline to -EPROTO, so we are able to detect the fixed kernel.
The optimized uprobe performance stays the same:
uprobe-nop : 3.129 ± 0.013M/s
uprobe-push : 3.045 ± 0.006M/s
uprobe-ret : 1.095 ± 0.004M/s
--> uprobe-nop10 : 7.170 ± 0.020M/s
uretprobe-nop : 2.143 ± 0.021M/s
uretprobe-push : 2.090 ± 0.000M/s
uretprobe-ret : 0.942 ± 0.000M/s
--> uretprobe-nop10: 3.381 ± 0.003M/s
usdt-nop : 3.245 ± 0.004M/s
--> usdt-nop10 : 7.256 ± 0.023M/s
[1] https://lore.kernel.org/bpf/[email protected]/
[2] https://lore.kernel.org/bpf/[email protected]/#t |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: zynqmp_dma: fix race between runtime PM and device removal
In zynqmp_dma_remove(), runtime PM was disabled only after checking
state and doing a manual suspend. This can race with runtime PM in the
remove/unbind (rmmod) path.
Disable runtime PM first, then suspend only if the device is not already
suspended. To prevent any further runtime PM transitions. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/rockchip: analogix_dp: Fix OF node reference leak via auto cleanup
Sashiko reported a reference leak in rockchip_dp_drm_encoder_enable(),
the of_get_child_by_name() function does not call of_node_put() in a
symmetrical way [1].
Fix the device node reference leak by using __free(device_node) to
automatically manage of_node_put() for all device nodes. |
