| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: fix locked bus on SMBus block-read of 0 (IRQ)
SMBus 3.1 6.5.7 allows a Block Read byte count of 0, but the
interrupt-driven block-read state machine rejects it as -EPROTO. Worse,
it returns without a NACK+STOP: the next receive cycle has already
started, so the target keeps holding SDA and the bus stays stuck until a
power cycle of this i2c controller.
Accept count=0: NACK the in-flight dummy byte (TXAK) and set msg->len to
2 so i2c_imx_isr_read_continue() emits STOP via its normal last-byte
path. The dummy byte is discarded; block-read callers only consume
buf[0..count-1].
Reading I2DR has likewise already armed the next byte on the
count > I2C_SMBUS_BLOCK_MAX error path, so NACK it (TXAK) before aborting
with -EPROTO; otherwise the failing transfer's STOP cannot complete and
the bus stays held.
The atomic path regressed earlier (v3.16) and is fixed separately; this
patch covers only the v6.13 state-machine rework. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: pch: use raw_spinlock_t for the register lock
pch_irq_type() is registered as the irq_chip .irq_set_type callback and
takes chip->spinlock with spin_lock_irqsave(). This callback is reached
from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while
the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled.
That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is
an rtmutex-backed sleeping lock, so acquiring it there is invalid.
This was confirmed on a PREEMPT_RT kernel with lockdep
(PROVE_RAW_LOCK_NESTING and DEBUG_ATOMIC_SLEEP). A grounded PoC mirrored
pch_irq_type()'s locking and drove it through the real genirq carrier
irq_set_irq_type() -> __irq_set_trigger() -> chip->irq_set_type(), i.e.
the same __irq_set_trigger() edge that __setup_irq() takes for a
requested IRQ. With the original spin_lock_irqsave() edge lockdep
reported an invalid wait context, immediately followed by:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 95, name: insmod
hardirqs last disabled at (3784): _raw_spin_lock_irqsave+0x4f/0x60
rt_spin_lock+0x3a/0x1c0
repro_irq_set_type+0x64/0xa0 [pch_repro]
__irq_set_trigger+0x69/0x140
irq_set_irq_type+0x78/0xd0
Switching the mirrored lock to raw_spinlock_t made both splats go away.
Convert the register lock to raw_spinlock_t. The same lock also
serializes the GPIO direction/value callbacks and the suspend/resume
register save/restore, but all of those critical sections only perform
MMIO register accesses (ioread32()/iowrite32()) and
irq_set_handler_locked(); none of them contain sleepable operations.
Keeping this register lock non-sleeping is therefore appropriate for the
irqchip callbacks and does not change the GPIO-side locking contract.
This is the same class of issue and fix as recently addressed for other
GPIO controllers, e.g. commit 286533cb14a3 ("gpio: sch: use raw_spinlock_t
in the irq startup path") and commit 90f0109019e6 ("gpio: eic-sprd: use
raw_spinlock_t in the irq startup path"). |
| Use-after-free in the DOM: Core & HTML component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| Use-after-free in the Graphics: ImageLib component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| Use-after-free in the Graphics: Text component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| Use-after-free in the JavaScript: WebAssembly component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: lock sk in iso_sock_getname
Accessing iso_pi(sk)->conn requires lock_sock, which is not held here.
Fix by adding the lock/release. |
| Use after free in Browser in Google Chrome on on Mac prior to 151.0.7922.169 allowed a remote attacker leveraging social engineering to execute arbitrary code outside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| Use after free in WebGL in Google Chrome prior to 151.0.7922.169 allowed a remote attacker to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| Valkey is a distributed key-value database. Prior to 7.2.14, 8.0.10, 8.1.9, 9.0.5, and 9.1.1, Valkey's RESTORE command accepts a malformed RDB stream payload that assigns one Pending Entry List NACK to multiple consumers during stream consumer-group deserialization, causing a use-after-free when one consumer is deleted while another still references the shared NACK and potentially allowing remote code execution. This issue is fixed in versions 7.2.14, 8.0.10, 8.1.9, 9.0.5, and 9.1.1. |
| libexpat before 2.8.4 lacks handler call depth tracking with custom encoding callbacks. Thus, a use-after-free can occur. NOTE: this is similar to CVE-2026-50219, CVE-2026-56131 and CVE-2026-56412. |
| Concurrent execution using shared resource with improper synchronization ('race condition') in Windows Device Health Attestation (DHA) allows an unauthorized attacker to execute code over a network. |
| A use-after-free issue was addressed with improved memory management. This issue is fixed in Safari 26.6, iOS 26.6 and iPadOS 26.6, macOS Tahoe 26.6, visionOS 26.6, watchOS 26.6. Processing maliciously crafted web content may lead to an unexpected Safari crash. |
| Use-after-free in the Layout: Text and Fonts component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: unlock i_mmap_rwsem before releasing after-split folios
__folio_split() keeps dereferencing the mapping after the split:
shmem_uncharge(mapping->host) and remap_page() while the folios are still
frozen/locked, and i_mmap_unlock_read(mapping) at the very end, after the
after-split folios have been unlocked and freed.
Nothing holds an inode reference across that. The split relies on @folio
-- which the beyond-EOF drop loop never removes, as it starts at
folio_next(folio) -- staying locked and in the page cache to hold off
eviction. But the unlock loop unlocks @folio before i_mmap_unlock_read()
runs. If the caller's @lock_at is a tail beyond EOF, as memory_failure()
passes when splitting a poisoned tail of a shmem THP that reaches past
i_size during truncation, it too is gone from the page cache; so once
@folio is unlocked no locked, in-cache folio pins the inode, and a
concurrent final iput() can evict and RCU-free it before
i_mmap_unlock_read() touches i_mmap_rwsem:
BUG: KASAN: slab-use-after-free in __up_read+0x634/0x790
i_mmap_unlock_read include/linux/fs.h:537 [inline]
__folio_split+0x732/0x1640 mm/huge_memory.c:4100
try_to_split_thp_page+0xab/0x390 mm/memory-failure.c:1675
memory_failure+0x1394/0x26e0 mm/memory-failure.c:2470
Freed by task 4601:
shmem_free_in_core_inode+0x54/0xb0 mm/shmem.c:5177
evict+0x57f/0xac0 fs/inode.c:870
Do every mapping dereference while @folio still pins the inode: drop
i_mmap_rwsem right after remap_page(), before the loop that unlocks and
frees the after-split folios, and clear @mapping so the exit path does not
unlock it again. shmem_uncharge() and remap_page() already run before
that point, so after this nothing past the unlock loop touches the inode
or the mapping.
This is now a rule the split depends on, alongside keeping @folio frozen
until the page cache is updated: no inode or mapping dereference once the
after-split folios start being unlocked. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: reset kernel-owned dev_info fields in ublk_ctrl_add_dev()
ublk_ctrl_add_dev() memcpy()s the userspace ublksrv_ctrl_dev_info into
ub->dev_info and then fixes up the fields the driver owns, but misses
->state and ->ublksrv_pid.
A device added with ->state = UBLK_S_DEV_LIVE passes the
"->state != UBLK_S_DEV_DEAD" test that ublk_stop_dev_unlocked() uses as its
proxy for "a disk is attached", while ->ub_disk is still NULL, so DEL_DEV
right after ADD_DEV oopses in del_gendisk(). UBLK_S_DEV_QUIESCED plus
UBLK_F_USER_RECOVERY dies one step earlier, in ublk_force_abort_dev(). A
poisoned ->state also gets START_USER_RECOVERY and the char device
read/write path onto a device that was never started, and wedges START_DEV
at -EEXIST. A poisoned ->ublksrv_pid just makes GET_DEV_INFO report an
unrelated task as the ublk server.
Reset both after the memcpy(), as ublk_detach_disk() does. Userspace only
ever reads these back, so correcting them silently breaks nothing.
ADD_DEV has copied ->state in unsanitized since ublk was merged, but back
then it was harmless: the gendisk was allocated during ADD_DEV, and both
teardown and the START_DEV -EEXIST check keyed off disk_live() rather than
->state. The oops became reachable once the disk allocation moved to
START_DEV and those checks switched to ->state. |
| Race condition, use-after-free in the Graphics component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add missing device refcount for CAN filter removal
sashiko-bot remarked a problem with a concurrent device unregistration
in isotp.c which also is present in the bcm.c code. A former fix for raw.c
commit c275a176e4b6 ("can: raw: add missing refcount for memory leak fix")
introduced a netdevice_tracker which solves the issue for bcm.c too.
bcm_release(), bcm_delete_rx_op() and bcm_notifier() relied on
dev_get_by_index(ifindex) to re-find the device for an rx_op before
unregistering its filter. If a concurrent NETDEV_UNREGISTER has already
unlisted the device from the ifindex table, that lookup fails and
can_rx_unregister() is silently skipped, leaving a stale CAN filter
pointing at the soon-to-be-freed bcm_op/socket.
Hold a netdev_hold()/netdev_put() tracked reference on op->rx_reg_dev
from the moment the rx filter is registered in bcm_rx_setup() until it
is unregistered in bcm_rx_unreg(), and use that reference directly in
bcm_release() and bcm_delete_rx_op() instead of re-looking the device
up by ifindex. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Fix use-after-free on vendor module reload
mmu_destroy_caches() destroys pte_list_desc_cache and
mmu_page_header_cache, but leaves both pointers unchanged. The pointers
live in kvm.ko, and therefore survive when a vendor module is unloaded
while kvm.ko remains loaded.
If creation of pte_list_desc_cache fails during a subsequent vendor
module load, its assignment sets pte_list_desc_cache to NULL and the
error path calls mmu_destroy_caches(). mmu_page_header_cache still
points to the cache destroyed during the preceding vendor module
unload. Passing that stale pointer to kmem_cache_destroy() causes a
slab use-after-free.
Reproduce the issue on a v7.1.3 kernel with CONFIG_KASAN=y,
CONFIG_KASAN_GENERIC=y, CONFIG_KVM=m, and CONFIG_KVM_INTEL=m. A
one-shot test hook forces pte_list_desc_cache to NULL on the second
invocation of kvm_mmu_vendor_module_init():
1. Load kvm.ko and kvm-intel.ko, creating both caches.
2. Unload only kvm_intel, leaving kvm.ko loaded.
3. Reload kvm_intel and force initialization through the -ENOMEM path.
KASAN reports:
BUG: KASAN: slab-use-after-free in
kvm_mmu_vendor_module_init+0x5b/0x170 [kvm]
...
kmem_cache_destroy+0x21/0x1d0
kvm_mmu_vendor_module_init+0x5b/0x170 [kvm]
...
Allocated by task 16817:
__kmem_cache_create_args+0x12c/0x3b0
__kmem_cache_create.constprop.0+0xb6/0xf0 [kvm]
kvm_mmu_vendor_module_init+0x13b/0x170 [kvm]
...
Freed by task 16820:
kmem_cache_destroy+0x117/0x1d0
kvm_mmu_vendor_module_exit+0x21/0x30 [kvm]
Clear both pointers immediately after destroying their caches so that
the stored state reflects the caches' lifetime and repeated cleanup is
safe.
With the fix applied, the same injected vendor module reload fails with
-ENOMEM as expected and produces no KASAN report. |
| In the Linux kernel, the following vulnerability has been resolved:
media: rtl2832: fix use-after-free in rtl2832_remove()
cancel_delayed_work_sync() is called before i2c_mux_del_adapters()
in rtl2832_remove(). While the cancel waits for any running instance
of i2c_gate_work to finish, it does not prevent the timer from being
rescheduled by a concurrent thread.
During probe, the r820t_attach() call attempts I2C transfers through
the mux adapter. These transfers go through i2c_mux_master_xfer(),
which calls rtl2832_deselect() after the transfer completes,
rescheduling i2c_gate_work via schedule_delayed_work(). If this
transfer is still in flight when rtl2832_remove() runs,
rtl2832_deselect() can reschedule i2c_gate_work after it has been
cancelled, causing a use-after-free when kfree(dev) is called.
Fix this by calling i2c_mux_del_adapters() before
cancel_delayed_work_sync(). Once the mux adapter is unregistered, no
new I2C transfers can go through it, so rtl2832_deselect() can no
longer reschedule i2c_gate_work. The subsequent
cancel_delayed_work_sync() is then guaranteed to be final. |
